The Better Mouse Trap Co. / sample paperwork

Basic — People, use and ergonomic design

BasicRevision C12026-10-24Planning draft18 entries
Basic — People, use and ergonomic designBMT-BASIC-CHECK-SHEET-ERGONOMICS-001 · Rev C1
Company
The Better Mouse Trap Co.
Project / product line
Basic trap
Document
Basic — People, use and ergonomic design
Document no.
BMT-BASIC-CHECK-SHEET-ERGONOMICS-001
Revision
C1
Status
Planning draft
Start date
2026-10-24
Revision date
2026-10-24
Prepared by / owner
Sam Reed, mechanical, BASIC-C1
Checklist ID
BMT-BASIC-CHECK-SHEET-ERGONOMICS-001, Rev C1
Scope
BASIC-C1 manual trap for an adult homeowner on the Wisconsin illustrative base.
Reviewer
Alex Meadow
Review date
2026-10-24
Team
Alex Meadow, packet owner; Sam Reed, mechanical lead; Robin Keel, animal-welfare reviewer; Ira Bell, Bell Sample Lab (test lab)
Approved by
Alex Meadow, Planning draft C1, 2026-10-24, not signed.
Basic — People, Use and Ergonomic Design
Item / review questionAnswer / findingResult / statusEvidenceResponsibility / action

Item ID: ERGONOMICS-01

Question: Who uses it, and who may struggle with it?

Answer / assumption: Intended user is a U.S. adult homeowner on the Wisconsin illustrative base. The unloaded-task list must include limited grip, low vision, and reduced dexterity, both hands, and a light household glove. Children and pets are bystanders, not operators. Alex Meadow is not the design body. No person in that set has been observed.

Explanation: BASIC-C1 is a manual one-mouse trap, proposed 180 × 70 × 65 mm and 0.18 kg, with a $24.00 hold price. BMT-BASIC-MARKET-CHECK-001 records 16 panels, 7 of 20 Grade B interviews, and 6 price choices. Cash collected is Not applicable — no transaction in this planning record. Those choices are not orders. This population screen is an input to CTQ03 (release grip) and CTQ06 (occupancy window), both due 2026-12-15. It does not show that those users can operate concept C1.

Result (Y/N/NA): N

Status: Open — not observed

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ03; CTQ06; BMT-BASIC-MARKET-CHECK-001, 16 panels, 6 price choices, $24.00 hold; C1 internal record only

Owner: Sam Reed

Next action: Write the inclusion list (grip, vision, dexterity, hand, glove, bystander) on BMT-BASIC-TEST-MATRIX-001 before 2026-12-15. Do not recruit. Sam Reed cannot assign spend.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-02

Question: Where and how will people use, carry and store it?

Answer / assumption: Place on a household floor along a wall, or on a low dry shelf. Carry empty and occupied with the window visible. Storage is dry. Release is manual and only after the keeper has a lawful place and permission. Outdoor set, wall-hung use above shoulder height, and any powered indicator are unchosen routes.

Explanation: The use site drives light, stoop, and wet-floor assumptions for later rows. Spec care is gloves, hygiene, and a visual check, with no sterilization claim. Frequency is a household pattern, not a shift. Nothing has been watched in a home.

Result (Y/N/NA): N

Status: Open — not observed

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; care line; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 steps 1 and 4; C1 internal record only

Owner: Sam Reed

Next action: Sketch one floor site and one shelf site, with reach height left blank until measured, before 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-03

Question: Can they grip, lift, reach and operate it comfortably?

Answer / assumption: Proposed mass is 0.18 kg, unmeasured. The release is an external slider that must keep fingers 30 mm clear of the door path (CTQ03). No hand belongs in the door path (DF03, severity 8, RPN 192). Peak set, release, and carry forces are unmeasured. No comfortable-force limit is adopted.

Explanation: At 0.18 kg the mass is a minor carry. The open ergonomic risks are pinch grip on a 180 mm body, finger path at the door, and a stoop at the baseboard. DF03 occurrence and detection are worksheet scores, not gauge data. Ten adult completions in CTQ03 are a proposed limit, not a result.

Result (Y/N/NA): N

Status: Open — not measured

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ03; DF03 RPN 192; mass 0.18 kg; C1 internal record only

Owner: Sam Reed

Next action: Hold force measurement until a C1 slider exists. File the 30 mm finger-clearance aim against CTQ03 before 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-04

Question: Can a first-time user understand controls and feedback?

Answer / assumption: Controls are an external release slider and a clear occupancy window, with plain set and release words. There is no app and no lamp. A first-time adult is expected to get set, check, and release from the object plus the draft card. Teach-back is planned and has not been run. Draft marking on the card is CONCEPT — NOT FOR USE.

Explanation: DP-03 and DP-04 on BMT-BASIC-DESIGN-PRINCIPLES-REVIEW-001 say the slider should map to the door and the window should show occupancy. Those lines are unrated. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 5 says hold the external grip away from the exit, open the slider, step away, and inspect. No novice has tried that sequence.

Result (Y/N/NA): N

Status: Open — not tried

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 steps 3 and 5; DP-03; DP-04; CTQ06; C1 internal record only

Owner: Sam Reed

Next action: Freeze the three words (set, check, release) on the draft card before 2026-12-15. Do not treat the card as passed.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-05

Question: What foreseeable misuse or contact could hurt someone?

Answer / assumption: Foreseeable contact is a door pinch (DF03, severity 8, RPN 192), bite or waste on the hands, an animal left too long (DF06, severity 9, RPN 432), and a bait pocket that comes off and could be mouthed (DF05, severity 9, RPN 162; CTQ05 captive after a 20 N pull). BASIC-C1 has no battery, so burn and shock are the unchosen electrical route. Children and pets can reach a floor unit.

Explanation: BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 1 says adult operator only, not a toy, fingers out of the entry path. Step 2 says gloves and no direct animal or waste contact. Robin Keel at Keel Sample Welfare has not set the check interval. Product action A06 (window and do-not-leave-unattended warning, due 2026-12-15) is blocked on that review. Company action A02 (welfare and release legality, due 2026-12-01) is a different row on the company log, and it is open. The insurance note to Nia Calder is unsent and due 2026-12-01. This row is not a CPSC clearance.

Result (Y/N/NA): N

Status: Open — not cleared

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF03 RPN 192; DF05 RPN 162; DF06 RPN 432; CTQ05; BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06;

Owner: Sam Reed

Next action: Copy DF03, DF05, and DF06 into the unsent broker note before 2026-12-01, and leave the welfare interval blank until Robin Keel writes it.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-06

Question: Can it be cleaned, maintained and put away?

Answer / assumption: The empty shell opens without tools (CTQ04). The person does not handle the animal. After a wash, the hinge and the latch are inspected before the next set. No sterilization claim. Gloves and a visual soil check are the care line. There is no electronics cassette to detach; that route is unchosen on BASIC-C1.

Explanation: DF04 is soiled corners retaining contamination, severity 8, RPN 240. The acceptance aim is no visible fluorescent soil after a defined wash, and it has not been run. Cleaning agents are unnamed. Disposal of a worn shell is ordinary plastic scrap in this draft, not a regulated take-back.

Result (Y/N/NA): N

Status: Open — not run

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ04; DF04 RPN 240; care line; C1 internal record only

Owner: Sam Reed

Next action: Name the wash method (water, agent, dry time) as an assumption on BMT-BASIC-WORK-INSTRUCTIONS-001 before 2026-12-15. Do not claim CTQ04 is met.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-07

Question: What did representative users actually do?

Answer / assumption: No representative user has been observed. BMT-BASIC-TEST-MATRIX-001 index TP-C1 indexes T03 as 10 unloaded adult users on the release grip, with fingers 30 mm from the door path. The BMT-BASIC-TEMPLATE-TEST-RESULTS-001 is empty (BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A16). Video and teach-back are not designed. Consent text is unwritten. T06, the occupancy-window check, is blocked until Robin Keel sets an interval (BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06, due 2026-12-15). A later small trial would be learning evidence, not proof about U.S. homeowners.

Explanation: Tests on BMT-BASIC-TEST-PLAN-001 and BMT-BASIC-TEST-MATRIX-001 are T01 through T14, all unrun. T01 through T06 is not the full set. CTQ01 through CTQ14 are untested. T03 and T06 are two empty indexes in that set, not a finished ergonomics study. Sam Reed owns the technical record and cannot spend. Alex Meadow owns any assignment into the $4,000.00 tests-and-welfare line on BMT-COMPANY-TEMPLATE-FUNDING-001 (action A12, closed 2026-10-11 as arithmetic only, not a deposit). No funds are committed.

Result (Y/N/NA): N

Status: Blocked — no participants

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; BMT-BASIC-TEST-MATRIX-001 index TP-C1 T03 and T06; BMT-BASIC-TEMPLATE-ACTION-LOG-001 actions A06 and A16;

Owner: Sam Reed

Next action: Leave T03 and T06 as empty indexes. Target review is 2026-12-15. Do not recruit.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-08

Question: Which design changes are required before the next prototype?

Answer / assumption: Before the next prototype: lengthen the release slider, round external corners, keep both vent banks open (CTQ02; DF02, severity 9, RPN 252), and add a positive open detent so a half-set is visible. Product action A03 already records the longer slider and the hold-open detent, due 2026-12-15, with no hardware built. Each change is traced to a stated need (finger path, soil, occupancy, latch state), owned by Sam Reed, and requires a retest. None is tooled.

Explanation: The $12,000.00 shell-mold allowance is BASIC-16 on BMT-BASIC-TEMPLATE-COST-SHEET-001, already described inside the $5.78 piece as $1.33 at 3,000 units a year for 3 years. It is not an order and it is not a supplier bid. The $12,000. BMT-BASIC-TEMPLATE-QUOTE-COMPARISON-001 has 18 dated bids, unawarded and with no purchase order, from Perry Voss at Fictional Sample Works, Willa Marsh at Fictional Meadow Prototype Shop, and Eden Crowe at Fictional Northline Molding. Stop before production tooling.

Result (Y/N/NA): N

Status: Open — not built

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ02; DF02 RPN 252; DF03 RPN 192; BASIC-16 $12,000.00 not ordered; C1 internal record only

Owner: Sam Reed

Next action: List the four changes against CTQ02, CTQ03, and DF03 on BMT-BASIC-CONCEPT-DRAWING-001 before 2026-12-15. Do not award a bid or issue a purchase order.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-09

Question: What hand sizes, grip spans, and gloves must the slider and shell fit?

Answer / assumption: Planning envelope only: smaller adult hand through larger adult hand, both hands, bare and with a light household glove. The dimensions to check are slider length and the 30 mm finger clearance in CTQ03, on the 180 × 70 × 65 mm body. No hand has been measured. No glove sample is on the bench. The preparer's hand is not the envelope.

Explanation: A glove adds bulk at the slider and can hide a short grip. Left-hand use is in scope because the household user is not specified as right-handed. Assistive needs beyond low vision, low grip, and low dexterity are not listed; they stay open rather than scored out.

Result (Y/N/NA): N

Status: Open — not measured

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ03 30 mm clearance; 180 × 70 × 65 mm; C1 internal record only

Owner: Sam Reed

Next action: Record 'hand envelope unmeasured' on BMT-BASIC-CONCEPT-DRAWING-001 before 2026-12-15, with glove type still unnamed.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-10

Question: What set, release, bait-load, and carry forces are proposed, and how will they be measured?

Answer / assumption: No force limit is declared. When C1 parts exist, measure peak set and release at the slider, and peak pull on the bait pocket against the CTQ05 aim (captive after 20 N on 10 units). Ten unloaded repeats are the plan, not a data set. Carry force at 0.18 kg is not the governing measurement. Gauge identity is unset. Ira Bell at Bell Sample Lab is not contacted.

Explanation: The evidence prompt forbids a universal comfortable force, so this sheet does not borrow one. DF03 RPN 192 stays a worksheet score until occurrence is tied to a measured force and a measured finger path. BASIC-15, the latch and vent gauge, has no purchase order; if a bid is later received, BMT-BASIC-BOM-001 says hold that spend in the $4,000.00 tests-and-welfare line.

Result (Y/N/NA): N

Status: Blocked — no gauge

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ05 20 N aim; DF03 RPN 192; BMT-BASIC-BOM-001 line BASIC-15, no bid on file; C1 internal record only

Owner: Sam Reed

Next action: Do not book a gauge. Note on BMT-BASIC-TEMPLATE-ACTION-LOG-001 that BMT-BASIC-BOM-001 line BASIC-15 has no bid on file, due with the other Basic evidence on 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-11

Question: Can the person see occupancy and latch state in the light where the unit actually sits?

Answer / assumption: Occupancy is a clear window, not a lamp (CTQ06). Assumed sites are a dim baseboard and a lit room. Contrast of the window and of the set/release words is not measured. Low vision stays on the trial list. Reading the window may require a stoop. There is no electronic indicator; that route is unchosen.

Explanation: DF06, severity 9, RPN 432, is the user leaving an occupied trap unchecked. A window that cannot be read in the real light makes that failure more likely. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 3 requires an in-person check and forbids relying on an alert. BASIC-C1 has no alert to rely on, which removes one failure and leaves the window as the only state cue.

Result (Y/N/NA): N

Status: Open — not measured

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ06; DF06 RPN 432; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 3; C1 internal record only

Owner: Sam Reed

Next action: State the two light cases (dim baseboard, lit room) as assumptions before 2026-12-15. Do not claim a contrast number.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-12

Question: What posture does placement and pickup force on the back, knees, shoulders, and wrists?

Answer / assumption: Proposed mass is 0.18 kg, so the load is not the issue and no lifting index is scored. The posture issue is a stoop or kneel at the baseboard and a pinch grip on a 180 mm body, for a placement and a pickup measured in seconds. Shelf placement, if used, is below shoulder height in this assumption. Wrist deviation at the slider is unmeasured.

Explanation: A lifting equation would mis-state this task. The harm path that matches the posture is DF03 (finger in the door path) during a hurried stoop, plus a missed window check under DF06. Duration is too short, on this estimate, to treat the household pattern as a repetitive-strain job.

Result (Y/N/NA): N

Status: Open — not observed

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; 0.18 kg and 180 × 70 × 65 mm; DF03; DF06; C1 internal record only

Owner: Sam Reed

Next action: Leave hand height and stoop angle blank on the concept sketch before 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-13

Question: How is bait loaded, and can the pocket or any loose piece be mouthed?

Answer / assumption: Bait is a molded insert that must stay captive after a 20 N pull on 10 units (CTQ05). Loading is by hand, with gloves called for in BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 2, and with no tool. DF05 is the holder detaching, severity 9, RPN 162. No pull test has been run. Children are not trial subjects. A loose pocket is treated as a mouthing hazard in the design screen, not as a passed small-parts test.

Explanation: The invention note names a captive bait pocket. That note is not a novelty finding and not a test. The unchosen route is a loose bait cup. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 2 says confirm the latch with no live animal, which is also the rule for any later handling trial.

Result (Y/N/NA): N

Status: Open — not run

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ05; DF05 RPN 162; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 2; C1 internal record only

Owner: Sam Reed

Next action: Keep CTQ05 at 'unrun' on this sheet. Due with Basic evidence on 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-14

Question: What does the person do if the latch is mis-set, the door is only partly closed, or the unit is dropped?

Answer / assumption: Intended safe state is a unit that is either clearly open or still contained, with no door travel while a finger is in the path. A positive open detent is required before the next prototype so a half-set is visible. Drop of an empty 0.18 kg shell is a corner-radius and latch-check issue. No drop trial, no mis-set trial, and no partial-latch trial has been run.

Explanation: DF01 is the door rebounding after entry, severity 7, RPN 210, which is an animal-containment failure the user must be able to see. Recovery words are not written beyond BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 5 (step away, inspect). Rounding corners is on the change list because a dropped shell is the foreseeable abuse of a floor object.

Result (Y/N/NA): N

Status: Open — not tried

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF01 RPN 210; DF03 RPN 192; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 5; C1 internal record only

Owner: Sam Reed

Next action: Add mis-set, partial latch, and empty drop to the unloaded-task index before 2026-12-15. Do not run them.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-15

Question: Can a first-time adult read the labels and teach back set, check, and release?

Answer / assumption: Words on the object and the draft card are set, check, and release, in English for the Wisconsin base. Other languages are not prepared. Type size and contrast are unspecified. Teach-back has not been run. T03 is only an empty index for 10 unloaded adult users on the slider. The card is marked CONCEPT — NOT FOR USE. Low vision remains on the inclusion list. No lawyer, welfare reviewer, or engineer has signed the card.

Explanation: Comprehension is DP-03, unrated. A homeowner who cannot teach back the check interval will feed DF06 (RPN 432). Robin Keel has not set that interval, so the card cannot yet state a number of hours. Leaving the interval blank is the honest draft.

Result (Y/N/NA): N

Status: Blocked — card not tried

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 basis line; DP-03; DF06 RPN 432; Robin Keel interval unset; C1 internal record only

Owner: Sam Reed

Next action: Do not print a check-interval number. Hold the card at draft until Robin Keel writes an interval or records that none is set. Sheet date for that hold is 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-16

Question: Who else can reach the mechanism, and what contact is foreseeable?

Answer / assumption: A child, a pet, or a guest can reach a floor unit. Contacts on the screen are the door path (DF03, RPN 192), the bait pocket (DF05, RPN 162), the vent openings (DF02, RPN 252, an animal-welfare path), and an animal left inside (DF06, RPN 432). BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 1 says place the trap out of reach of children and pets. How that is done in a real room is not shown.

Explanation: The insurance note to Nia Calder at Calder Sample Risk is not sent. No premium is paid and no policy is bound. This row feeds that note; it does not clear a consumer-product question. Tip-over of a 0.18 kg shell is a low-energy event; the harm is contact with the animal or the door, not the falling mass.

Result (Y/N/NA): N

Status: Open — not observed

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF02 RPN 252; DF03; DF05; DF06; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 1; C1 internal record only

Owner: Sam Reed

Next action: Add the bystander contacts to the unsent broker packet list before 2026-12-01. Owner of the technical line remains Sam Reed.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-17

Question: How often is each task repeated, and for how long?

Answer / assumption: Household pattern assumed, not timed: a few sets in a week while a problem is active, a look at the window on the days the trap is set, and a wash when the shell is soiled. Each task is seconds to about a minute. Repetition is a lower concern than pinch, hygiene, and an animal left unchecked. Robin Keel has not set the check interval, so 'daily' is not a protocol.

Explanation: DF06 RPN 432 grows if the real interval is longer than the user remembers. Company action A02 (welfare and release legality, Sam Reed, due 2026-12-01) is the legality note. Product action A06 (due 2026-12-15) is the warning text, and it is blocked until Robin Keel sets an interval. This sheet does not invent hours. The pattern is not a production job and is not scored as one.

Result (Y/N/NA): N

Status: Open — not timed

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF06 RPN 432; BMT-COMPANY-TEMPLATE-ACTION-LOG-001 action A02 due 2026-12-01; BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06 due

Owner: Sam Reed

Next action: Cross-check this row to BMT-COMPANY-TEMPLATE-ACTION-LOG-001 action A02 before 2026-12-01 and to BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06 before 2026-12-15. Leave hours blank.

Reviewer / review date: Alex Meadow, 2026-10-24

Item ID: ERGONOMICS-18

Question: Which ergonomic changes and trials sit inside an authorized budget, and which are blocked?

Answer / assumption: The geometry changes and the user index are paper. No purchase order exists. Product action A03 (extend the slider and add a hold-open detent, due 2026-12-15) has no hardware. Action A12 (Alex Meadow, closed 2026-10-11) is arithmetic only, not a deposit. The adopted split on BMT-COMPANY-TEMPLATE-FUNDING-001 and BMT-BASIC-FUNDING-WORKSHEET-001 is prototype $5,000.00 (T1), tests and welfare $4,000.00 (T2), market research $2,000.00 (T3), design $2,000.00 (T4), and unallocated reserve $2,000.00 (T5). Nothing is drawn. Each release needs a written consent from Alex Meadow that names the line. BMT-BASIC-BOM-001 line BASIC-15 points at the $4,000.00 tests-and-welfare line for a gauge with no bid on file. A later user trial would need Alex Meadow to assign it to that $4,000.00 line. The $12,000. The $24.00 price is a hold, not revenue. The $80,000.00 owner-capital plan is not deposited.

Explanation: Sam Reed cannot spend and cannot speak for the company. Perry Voss at Fictional Sample Works, Willa Marsh at Fictional Meadow Prototype Shop, and Eden Crowe at Fictional Northline Molding have dated bids on BMT-BASIC-TEMPLATE-QUOTE-COMPARISON-001 (18 bids). Those bids are unawarded and there is no purchase order. The $12,000.00 allowance is not one of those bids. Every ergonomic action on this sheet is blocked on evidence and on an assignment of money. Stop before production tooling.

Result (Y/N/NA): N

Status: Blocked — no spend

BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; action A12 closed 2026-10-11 as arithmetic only; BMT-COMPANY-TEMPLATE-FUNDING-001 and BMT-BASIC-FUNDING-WORKSHEET-001

Owner: Sam Reed

Next action: Leave spend at zero. Follow the adopted five-line split on BMT-COMPANY-TEMPLATE-FUNDING-001 and BMT-BASIC-FUNDING-WORKSHEET-001. Do not start a trial from this sheet. Gate for the open technical lines remains 2026-12-15.

Reviewer / review date: Alex Meadow, 2026-10-24

Basic — People, Use and Ergonomic Design — supporting detail

Basic — Who uses it, and who may struggle with it?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-01

Question. Who uses it, and who may struggle with it?

Evidence to record. Actual intended ages, abilities, hand/body sizes, left/right-handed use, strength, gloves and assistive needs. Do not design only for the founder or an average body.

Answer / assumption. Intended user is a U.S. adult homeowner on the Wisconsin illustrative base. The unloaded-task list must include limited grip, low vision, and reduced dexterity, both hands, and a light household glove. Children and pets are bystanders, not operators. Alex Meadow is not the design body. No person in that set has been observed.

Status. Open — not observed

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ03; CTQ06; BMT-BASIC-MARKET-CHECK-001, 16 panels, 6 price choices, $24.00 hold; C1 internal record only

Owner. Sam Reed

Next action. Write the inclusion list (grip, vision, dexterity, hand, glove, bystander) on BMT-BASIC-TEST-MATRIX-001 before 2026-12-15. Do not recruit. Sam Reed cannot assign spend.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Basic — Where and how will people use, carry and store it?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-02

Question. Where and how will people use, carry and store it?

Evidence to record. Lighting, wet/dirty use, temperature, clothing, workspace, reach, frequency, duration and one- versus two-handed tasks.

Answer / assumption. Place on a household floor along a wall, or on a low dry shelf. Carry empty and occupied with the window visible. Storage is dry. Release is manual and only after the keeper has a lawful place and permission. Outdoor set, wall-hung use above shoulder height, and any powered indicator are unchosen routes.

Explanation. The use site drives light, stoop, and wet-floor assumptions for later rows. Spec care is gloves, hygiene, and a visual check, with no sterilization claim. Frequency is a household pattern, not a shift. Nothing has been watched in a home.

Status. Open — not observed

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; care line; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 steps 1 and 4; C1 internal record only

Owner. Sam Reed

Next action. Sketch one floor site and one shelf site, with reach height left blank until measured, before 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Basic — Can they grip, lift, reach and operate it comfortably?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-03

Question. Can they grip, lift, reach and operate it comfortably?

Evidence to record. Observe posture, reach, grip span, contact pressure, weight, balance, repetition and required force. Measure relevant dimensions and effort; do not invent a universal comfortable force.

Answer / assumption. Proposed mass is 0.18 kg, unmeasured. The release is an external slider that must keep fingers 30 mm clear of the door path (CTQ03). No hand belongs in the door path (DF03, severity 8, RPN 192). Peak set, release, and carry forces are unmeasured. No comfortable-force limit is adopted.

Explanation. At 0.18 kg the mass is a minor carry. The open ergonomic risks are pinch grip on a 180 mm body, finger path at the door, and a stoop at the baseboard. DF03 occurrence and detection are worksheet scores, not gauge data. Ten adult completions in CTQ03 are a proposed limit, not a result.

Status. Open — not measured

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ03; DF03 RPN 192; mass 0.18 kg; C1 internal record only

Owner. Sam Reed

Next action. Hold force measurement until a C1 slider exists. File the 30 mm finger-clearance aim against CTQ03 before 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH hand-tool ergonomics booklet, public guidance, read 2026-10-24

Basic — Can a first-time user understand controls and feedback?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-04

Question. Can a first-time user understand controls and feedback?

Evidence to record. Setup, labels, visibility, tactile cues, mistakes, recovery and instructions; accessibility needs and actual observed misunderstandings.

Answer / assumption. Controls are an external release slider and a clear occupancy window, with plain set and release words. There is no app and no lamp. A first-time adult is expected to get set, check, and release from the object plus the draft card. Teach-back is planned and has not been run. Draft marking on the card is CONCEPT — NOT FOR USE.

Explanation. DP-03 and DP-04 on BMT-BASIC-DESIGN-PRINCIPLES-REVIEW-001 say the slider should map to the door and the window should show occupancy. Those lines are unrated. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 5 says hold the external grip away from the exit, open the slider, step away, and inspect. No novice has tried that sequence.

Status. Open — not tried

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 steps 3 and 5; DP-03; DP-04; CTQ06; C1 internal record only

Owner. Sam Reed

Next action. Freeze the three words (set, check, release) on the draft card before 2026-12-15. Do not treat the card as passed.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — What foreseeable misuse or contact could hurt someone?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-05

Question. What foreseeable misuse or contact could hurt someone?

Evidence to record. Pinch, cut, burn, tip, choke, electrical and other applicable hazards, including children/bystanders. Feed design changes and safety requirements to Sam Reed.

Answer / assumption. Foreseeable contact is a door pinch (DF03, severity 8, RPN 192), bite or waste on the hands, an animal left too long (DF06, severity 9, RPN 432), and a bait pocket that comes off and could be mouthed (DF05, severity 9, RPN 162; CTQ05 captive after a 20 N pull). BASIC-C1 has no battery, so burn and shock are the unchosen electrical route. Children and pets can reach a floor unit.

Explanation. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 1 says adult operator only, not a toy, fingers out of the entry path. Step 2 says gloves and no direct animal or waste contact. Robin Keel at Keel Sample Welfare has not set the check interval. Product action A06 (window and do-not-leave-unattended warning, due 2026-12-15) is blocked on that review. Company action A02 (welfare and release legality, due 2026-12-01) is a different row on the company log, and it is open. The insurance note to Nia Calder is unsent and due 2026-12-01. This row is not a CPSC clearance.

Status. Open — not cleared

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF03 RPN 192; DF05 RPN 162; DF06 RPN 432; CTQ05; BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06; BMT-COMPANY-TEMPLATE-ACTION-LOG-001 action A02; C1 internal record only

Owner. Sam Reed

Next action. Copy DF03, DF05, and DF06 into the unsent broker note before 2026-12-01, and leave the welfare interval blank until Robin Keel writes it.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — Can it be cleaned, maintained and put away?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-06

Question. Can it be cleaned, maintained and put away?

Evidence to record. Contact materials, residues, cleaning agents, disassembly, consumables, storage, service and disposal scenarios.

Answer / assumption. The empty shell opens without tools (CTQ04). The person does not handle the animal. After a wash, the hinge and the latch are inspected before the next set. No sterilization claim. Gloves and a visual soil check are the care line. There is no electronics cassette to detach; that route is unchosen on BASIC-C1.

Explanation. DF04 is soiled corners retaining contamination, severity 8, RPN 240. The acceptance aim is no visible fluorescent soil after a defined wash, and it has not been run. Cleaning agents are unnamed. Disposal of a worn shell is ordinary plastic scrap in this draft, not a regulated take-back.

Status. Open — not run

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ04; DF04 RPN 240; care line; C1 internal record only

Owner. Sam Reed

Next action. Name the wash method (water, agent, dry time) as an assumption on BMT-BASIC-WORK-INSTRUCTIONS-001 before 2026-12-15. Do not claim CTQ04 is met.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — What did representative users actually do?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-07

Question. What did representative users actually do?

Evidence to record. Prototype revision, participants and relevant characteristics, tasks, consent, observations, errors, discomfort, completion measures and limits. Small trials are learning evidence, not population-wide proof.

Answer / assumption. No representative user has been observed. BMT-BASIC-TEST-MATRIX-001 index TP-C1 indexes T03 as 10 unloaded adult users on the release grip, with fingers 30 mm from the door path. The BMT-BASIC-TEMPLATE-TEST-RESULTS-001 is empty (BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A16). Video and teach-back are not designed. Consent text is unwritten. T06, the occupancy-window check, is blocked until Robin Keel sets an interval (BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06, due 2026-12-15). A later small trial would be learning evidence, not proof about U.S. homeowners.

Explanation. Tests on BMT-BASIC-TEST-PLAN-001 and BMT-BASIC-TEST-MATRIX-001 are T01 through T14, all unrun. T01 through T06 is not the full set. CTQ01 through CTQ14 are untested. T03 and T06 are two empty indexes in that set, not a finished ergonomics study. Sam Reed owns the technical record and cannot spend. Alex Meadow owns any assignment into the $4,000.00 tests-and-welfare line on BMT-COMPANY-TEMPLATE-FUNDING-001 (action A12, closed 2026-10-11 as arithmetic only, not a deposit). No funds are committed.

Status. Blocked — no participants

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; BMT-BASIC-TEST-MATRIX-001 index TP-C1 T03 and T06; BMT-BASIC-TEMPLATE-ACTION-LOG-001 actions A06 and A16; BMT-COMPANY-TEMPLATE-ACTION-LOG-001 action A12; $4,000.00 tests-and-welfare line; C1 internal record only

Owner. Sam Reed

Next action. Leave T03 and T06 as empty indexes. Target review is 2026-12-15. Do not recruit.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Basic — Which design changes are required before the next prototype?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-08

Question. Which design changes are required before the next prototype?

Evidence to record. Trace each requirement/change to an observation or stated need, owner and retest. Keep aesthetics, usability and engineering feasibility linked.

Answer / assumption. Before the next prototype: lengthen the release slider, round external corners, keep both vent banks open (CTQ02; DF02, severity 9, RPN 252), and add a positive open detent so a half-set is visible. Product action A03 already records the longer slider and the hold-open detent, due 2026-12-15, with no hardware built. Each change is traced to a stated need (finger path, soil, occupancy, latch state), owned by Sam Reed, and requires a retest. None is tooled.

Status. Open — not built

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ02; DF02 RPN 252; DF03 RPN 192; BASIC-16 $12,000.00 not ordered; C1 internal record only

Owner. Sam Reed

Next action. List the four changes against CTQ02, CTQ03, and DF03 on BMT-BASIC-CONCEPT-DRAWING-001 before 2026-12-15. Do not award a bid or issue a purchase order.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Basic — What hand sizes, grip spans, and gloves must the slider and shell fit?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-09

Question. What hand sizes, grip spans, and gloves must the slider and shell fit?

Evidence to record. State the hand-breadth and grip-span envelope, dominant and non-dominant hand, bare hand, and the glove the task expects. Record a dimension aim on concept C1 for the slider and the shell. Do not treat the preparer's hand as the envelope.

Answer / assumption. Planning envelope only: smaller adult hand through larger adult hand, both hands, bare and with a light household glove. The dimensions to check are slider length and the 30 mm finger clearance in CTQ03, on the 180 × 70 × 65 mm body. No hand has been measured. No glove sample is on the bench. The preparer's hand is not the envelope.

Explanation. A glove adds bulk at the slider and can hide a short grip. Left-hand use is in scope because the household user is not specified as right-handed. Assistive needs beyond low vision, low grip, and low dexterity are not listed; they stay open rather than scored out.

Status. Open — not measured

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ03 30 mm clearance; 180 × 70 × 65 mm; C1 internal record only

Owner. Sam Reed

Next action. Record 'hand envelope unmeasured' on BMT-BASIC-CONCEPT-DRAWING-001 before 2026-12-15, with glove type still unnamed.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH hand-tool ergonomics booklet, public guidance, read 2026-10-24

Basic — What set, release, bait-load, and carry forces are proposed, and how will they be measured?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-10

Question. What set, release, bait-load, and carry forces are proposed, and how will they be measured?

Evidence to record. Name the gauge, the grip, the number of repeats, and who would be measured. Record peak force and the point of application for set, release, bait load, and carry. Do not publish one comfortable-force number.

Answer / assumption. No force limit is declared. When C1 parts exist, measure peak set and release at the slider, and peak pull on the bait pocket against the CTQ05 aim (captive after 20 N on 10 units). Ten unloaded repeats are the plan, not a data set. Carry force at 0.18 kg is not the governing measurement. Gauge identity is unset. Ira Bell at Bell Sample Lab is not contacted.

Explanation. The evidence prompt forbids a universal comfortable force, so this sheet does not borrow one. DF03 RPN 192 stays a worksheet score until occurrence is tied to a measured force and a measured finger path. BASIC-15, the latch and vent gauge, has no purchase order; if a bid is later received, BMT-BASIC-BOM-001 says hold that spend in the $4,000.00 tests-and-welfare line.

Status. Blocked — no gauge

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ05 20 N aim; DF03 RPN 192; BMT-BASIC-BOM-001 line BASIC-15, no bid on file; C1 internal record only

Owner. Sam Reed

Next action. Do not book a gauge. Note on BMT-BASIC-TEMPLATE-ACTION-LOG-001 that BMT-BASIC-BOM-001 line BASIC-15 has no bid on file, due with the other Basic evidence on 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH hand-tool ergonomics booklet, public guidance, read 2026-10-24

Basic — Can the person see occupancy and latch state in the light where the unit actually sits?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-11

Question. Can the person see occupancy and latch state in the light where the unit actually sits?

Evidence to record. Record the light at the real site (day, room lamp, closet, service hall, dock), window contrast, label contrast, and whether latch state is visible without kneeling into the unit. A bench photo is not the use site.

Answer / assumption. Occupancy is a clear window, not a lamp (CTQ06). Assumed sites are a dim baseboard and a lit room. Contrast of the window and of the set/release words is not measured. Low vision stays on the trial list. Reading the window may require a stoop. There is no electronic indicator; that route is unchosen.

Explanation. DF06, severity 9, RPN 432, is the user leaving an occupied trap unchecked. A window that cannot be read in the real light makes that failure more likely. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 3 requires an in-person check and forbids relying on an alert. BASIC-C1 has no alert to rely on, which removes one failure and leaves the window as the only state cue.

Status. Open — not measured

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ06; DF06 RPN 432; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 3; C1 internal record only

Owner. Sam Reed

Next action. State the two light cases (dim baseboard, lit room) as assumptions before 2026-12-15. Do not claim a contrast number.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Basic — What posture does placement and pickup force on the back, knees, shoulders, and wrists?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-12

Question. What posture does placement and pickup force on the back, knees, shoulders, and wrists?

Evidence to record. Sketch reach height, kneel or stoop, wrist angle at the slider, and how long the posture is held. Separate empty placement from occupied pickup. Do not score a lifting index until mass and hand height are measured.

Answer / assumption. Proposed mass is 0.18 kg, so the load is not the issue and no lifting index is scored. The posture issue is a stoop or kneel at the baseboard and a pinch grip on a 180 mm body, for a placement and a pickup measured in seconds. Shelf placement, if used, is below shoulder height in this assumption. Wrist deviation at the slider is unmeasured.

Explanation. A lifting equation would mis-state this task. The harm path that matches the posture is DF03 (finger in the door path) during a hurried stoop, plus a missed window check under DF06. Duration is too short, on this estimate, to treat the household pattern as a repetitive-strain job.

Status. Open — not observed

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; 0.18 kg and 180 × 70 × 65 mm; DF03; DF06; C1 internal record only

Owner. Sam Reed

Next action. Leave hand height and stoop angle blank on the concept sketch before 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH hand-tool ergonomics booklet, public guidance, read 2026-10-24

Basic — How is bait loaded, and can the pocket or any loose piece be mouthed?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-13

Question. How is bait loaded, and can the pocket or any loose piece be mouthed?

Evidence to record. Record the bait-load steps, whether a tool is required, the captive-pull aim, and any piece that can separate. Tie mouthing and choke screening to the bait-pocket requirement. No child is a trial subject.

Answer / assumption. Bait is a molded insert that must stay captive after a 20 N pull on 10 units (CTQ05). Loading is by hand, with gloves called for in BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 2, and with no tool. DF05 is the holder detaching, severity 9, RPN 162. No pull test has been run. Children are not trial subjects. A loose pocket is treated as a mouthing hazard in the design screen, not as a passed small-parts test.

Explanation. The invention note names a captive bait pocket. That note is not a novelty finding and not a test. The unchosen route is a loose bait cup. BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 2 says confirm the latch with no live animal, which is also the rule for any later handling trial.

Status. Open — not run

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; CTQ05; DF05 RPN 162; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 2; C1 internal record only

Owner. Sam Reed

Next action. Keep CTQ05 at 'unrun' on this sheet. Due with Basic evidence on 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — What does the person do if the latch is mis-set, the door is only partly closed, or the unit is dropped?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-14

Question. What does the person do if the latch is mis-set, the door is only partly closed, or the unit is dropped?

Evidence to record. Walk mis-set, partial latch, and drop on an empty unit. Record whether the door can travel onto a finger, whether state stays obvious, and the recovery words. Keep the safe state explicit.

Answer / assumption. Intended safe state is a unit that is either clearly open or still contained, with no door travel while a finger is in the path. A positive open detent is required before the next prototype so a half-set is visible. Drop of an empty 0.18 kg shell is a corner-radius and latch-check issue. No drop trial, no mis-set trial, and no partial-latch trial has been run.

Explanation. DF01 is the door rebounding after entry, severity 7, RPN 210, which is an animal-containment failure the user must be able to see. Recovery words are not written beyond BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 5 (step away, inspect). Rounding corners is on the change list because a dropped shell is the foreseeable abuse of a floor object.

Status. Open — not tried

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF01 RPN 210; DF03 RPN 192; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 5; C1 internal record only

Owner. Sam Reed

Next action. Add mis-set, partial latch, and empty drop to the unloaded-task index before 2026-12-15. Do not run them.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — Can a first-time adult read the labels and teach back set, check, and release?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-15

Question. Can a first-time adult read the labels and teach back set, check, and release?

Evidence to record. Record type size, contrast, the words on the object and the card, language, and whether a first-time adult can teach back set, check, and release without coaching. A draft card is not comprehension evidence.

Answer / assumption. Words on the object and the draft card are set, check, and release, in English for the Wisconsin base. Other languages are not prepared. Type size and contrast are unspecified. Teach-back has not been run. T03 is only an empty index for 10 unloaded adult users on the slider. The card is marked CONCEPT — NOT FOR USE. Low vision remains on the inclusion list. No lawyer, welfare reviewer, or engineer has signed the card.

Explanation. Comprehension is DP-03, unrated. A homeowner who cannot teach back the check interval will feed DF06 (RPN 432). Robin Keel has not set that interval, so the card cannot yet state a number of hours. Leaving the interval blank is the honest draft.

Status. Blocked — card not tried

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 basis line; DP-03; DF06 RPN 432; Robin Keel interval unset; C1 internal record only

Owner. Sam Reed

Next action. Do not print a check-interval number. Hold the card at draft until Robin Keel writes an interval or records that none is set. Sheet date for that hold is 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — Who else can reach the mechanism, and what contact is foreseeable?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-16

Question. Who else can reach the mechanism, and what contact is foreseeable?

Evidence to record. Name children, pets, guests, coworkers, and bystanders at the site. Record reach into the door path, bait, vents, cassette, and, where fitted, a rotor or carriage. Feed any new hazard to Sam Reed and the unsent insurance note.

Answer / assumption. A child, a pet, or a guest can reach a floor unit. Contacts on the screen are the door path (DF03, RPN 192), the bait pocket (DF05, RPN 162), the vent openings (DF02, RPN 252, an animal-welfare path), and an animal left inside (DF06, RPN 432). BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 1 says place the trap out of reach of children and pets. How that is done in a real room is not shown.

Explanation. The insurance note to Nia Calder at Calder Sample Risk is not sent. No premium is paid and no policy is bound. This row feeds that note; it does not clear a consumer-product question. Tip-over of a 0.18 kg shell is a low-energy event; the harm is contact with the animal or the door, not the falling mass.

Status. Open — not observed

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF02 RPN 252; DF03; DF05; DF06; BMT-BASIC-INSTRUCTIONS-AND-WARNINGS-001 step 1; C1 internal record only

Owner. Sam Reed

Next action. Add the bystander contacts to the unsent broker packet list before 2026-12-01. Owner of the technical line remains Sam Reed.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. https://www.cpsc.gov/Business--Manufacturing (CPSC business/manufacturing page), the CPSC small-business page, the CPSC regulatory-robot page, and CPSIA children's-product material: source status to find — not opened, logged 2026-10-24 on BMT-BASIC-COMPLIANCE-01-001 and BMT-BASIC-REGULATORY-SCREENING-001. No clause extract. No CPSC-accepted lab. The EPA device page opened the same day is not a CPSC read.

Basic — How often is each task repeated, and for how long?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-17

Question. How often is each task repeated, and for how long?

Evidence to record. Estimate sets, checks, carries, and washes per week for the intended user. Separate a household pattern from a work shift or a research crew. Do not turn the estimate into a strain score without timings.

Answer / assumption. Household pattern assumed, not timed: a few sets in a week while a problem is active, a look at the window on the days the trap is set, and a wash when the shell is soiled. Each task is seconds to about a minute. Repetition is a lower concern than pinch, hygiene, and an animal left unchecked. Robin Keel has not set the check interval, so 'daily' is not a protocol.

Explanation. DF06 RPN 432 grows if the real interval is longer than the user remembers. Company action A02 (welfare and release legality, Sam Reed, due 2026-12-01) is the legality note. Product action A06 (due 2026-12-15) is the warning text, and it is blocked until Robin Keel sets an interval. This sheet does not invent hours. The pattern is not a production job and is not scored as one.

Status. Open — not timed

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; DF06 RPN 432; BMT-COMPANY-TEMPLATE-ACTION-LOG-001 action A02 due 2026-12-01; BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06 due 2026-12-15; Robin Keel; C1 internal record only

Owner. Sam Reed

Next action. Cross-check this row to BMT-COMPANY-TEMPLATE-ACTION-LOG-001 action A02 before 2026-12-01 and to BMT-BASIC-TEMPLATE-ACTION-LOG-001 action A06 before 2026-12-15. Leave hours blank.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Basic — Which ergonomic changes and trials sit inside an authorized budget, and which are blocked?

Project. Basic

Product revision. C1

Sheet revision. 1

Prepared by. Sam Reed

Date. 2026-10-24

Target market / jurisdiction. U.S. adults; Wisconsin illustrative base

Decision being prepared. Next private feasibility gate

Sheet. People, Use and Ergonomic Design

Lead. Sam Reed

Item ID. ERGONOMICS-18

Question. Which ergonomic changes and trials sit inside an authorized budget, and which are blocked?

Evidence to record. Tie each trial and tool change to a named money slice, a decision-log date, and the person who can assign spend. State what is blocked. A hypothesis price is not funding.

Explanation. Sam Reed cannot spend and cannot speak for the company. Perry Voss at Fictional Sample Works, Willa Marsh at Fictional Meadow Prototype Shop, and Eden Crowe at Fictional Northline Molding have dated bids on BMT-BASIC-TEMPLATE-QUOTE-COMPARISON-001 (18 bids). Those bids are unawarded and there is no purchase order. The $12,000.00 allowance is not one of those bids. Every ergonomic action on this sheet is blocked on evidence and on an assignment of money. Stop before production tooling.

Status. Blocked — no spend

Result (Y/N/NA). N

Evidence / exact revision / URL and date. BMT-BASIC-SPEC-SHEET-001 Rev C1, recorded 2026-10-24; action A12 closed 2026-10-11 as arithmetic only; BMT-COMPANY-TEMPLATE-FUNDING-001 and BMT-BASIC-FUNDING-WORKSHEET-001 tests-and-welfare line $4,000.00, tranches T1 through T5, nothing drawn; BMT-BASIC-BOM-001 lines BASIC-15 and BASIC-16; $24.00 hold; C1 internal record only

Owner. Sam Reed

Next action. Leave spend at zero. Follow the adopted five-line split on BMT-COMPANY-TEMPLATE-FUNDING-001 and BMT-BASIC-FUNDING-WORKSHEET-001. Do not start a trial from this sheet. Gate for the open technical lines remains 2026-12-15.

Reviewer / review date. Alex Meadow, 2026-10-24

Not-applicable reason. Applies

Source guidance URLs. NIOSH ergonomics topic page, public guidance, read 2026-10-24

Document administration

Preparation: Sam Reed, scenario attribution, 2026-10-24. Signature: unsigned. Review: pending; no reviewer signature or date. Approval: withheld; no approver signature or date.

Prepared byDate
Reviewed byDate
Approved byDate