- Company
- The Better Mouse Trap Co.
- Project / product line
- Drone trap
- Document
- Drone Trap — Suppliers and production readiness
- Document no.
- BMT-DRONE-CHECK-SHEET-PRODUCTION-001
- Revision
- C1
- Status
- Planning draft
- Start date
- 2026-10-24
- Revision date
- 2026-10-24
- Prepared by / owner
- Jordan Vale, flight research, DRONE-C1
- Checklist ID
- BMT-DRONE-CHECK-SHEET-PRODUCTION-001, Rev C1
- Scope
- DRONE-C1 supplier readiness for the capsule and the buy-item airframe.
- Reviewer
- Casey Holt
- Review date
- Planned 2026-11-01. Pending as of 2026-10-28. The review has not been held.
- Team
- Alex Meadow, packet owner and no-flight gate; Jordan Vale, flight research; Sam Reed, mechanical interface; Robin Keel,
- Approved by
- review pending.
| Item / review question | Answer / finding | Result / status | Evidence | Responsibility / action |
|---|---|---|---|---|
Item ID: PRODUCTION-01 Question: Are all suppliers quoting the same thing? | Answer / assumption: Thirty-three dated bids are on BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1, refs FSW-D-2026-01 through NLM-D-2026-33, parts DRONE-01 through DRONE-11, unawarded, no purchase order, cash disbursed Not applicable — no transaction in this planning record. The obsolete two-supplier blank sheet is withdrawn. DRONE-01 capsule bids: FSW-D-2026-01 (Fictional Sample Works, Perry Voss) dated 2026-10-02, valid through 2026-12-31, P20 capsule mold, 1 cavity, 200,000 shots, tooling $72,400.00, volume piece $11.80, annual qty 100, tool lead 18 weeks, tool owner: The Better Mouse Trap Co. when paid. MPS-D-2026-02 (Fictional Meadow Prototype Shop, Willa Marsh) dated 2026-10-06, valid through 2026-12-05, Aluminum capsule bridge mold, 1 cavity, 15,000 shots, tooling $22,500.00, volume piece $24.50, annual qty 10, tool lead 7 weeks, tool owner: Meadow Prototype Shop until buyout. NLM-D-2026-03 (Fictional Northline Molding, Eden Crowe) dated 2026-10-09, valid through 2027-01-07, Pre-hard capsule mold, 1 cavity, 120,000 shots, tooling $54,800.00, volume piece $14.20, annual qty 100, tool lead 15 weeks, tool owner: The Better Mouse Trap Co. before kickoff. The internal $60,000.00 capsule allowance is outside the $250,000.00 ceiling and is not one of those bids. Drawings are not released, so the bids are not one common released revision. The company correspondence log has no outbound letter to Perry Voss, Willa Marsh, or Eden Crowe. That gap does not erase the bids. BOM C1 splits DRONE-12, DRONE-13, and DRONE-15 through DRONE-17 as included cost inside the $540.00 pre-tool sum. DRONE-14 remote ID at $18.00 stays excluded from the piece sum and is not a selected part. BOM C1 records a labor-line name clash on DRONE-10: the cost sheet still names Fictional Sample Works, and the BOM says that name is not an order. Year-1 commercial units authorized: 0. No flight. The 100-a-year column is a cost case, not a forecast. Explanation: G1 is Hold tooling pending evidence. Thirty-three unawarded bids do not create a flight supplier and do not authorize outdoor flight. A reader who treats $740.00 or the $60,000.00 allowance as an awarded price is reading the cost sheet. Year-1 commercial units authorized: 0. | Result (Y/N/NA): N Status: Open — bids unawarded, drawing not released | BMT-DRONE-BOM-001 Rev C1 DRONE-01 through DRONE-18; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1, 33 dated bids, FSW-D-2026-01 through NLM-D-2026-33, unawarded. | Owner: Jordan Vale Next action: Jordan Vale does not award a bid and does not imply a flight shop from the quote contacts. No purchase order. Target 2027-06-15, planned. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Thirty-three bids stay unawarded. There is no common released offer and no purchase order. |
Item ID: PRODUCTION-02 Question: Can the supplier actually make and inspect it? | Answer / assumption: No audit or capability study. The thirty-three bids are not an audit. No process limit, sample, quality-system scope, or production address is on file beyond the quote rows. Perry Voss, Willa Marsh, and Eden Crowe are quote contacts on DRONE-01 through DRONE-11. Those bids do not show a qualified composite shop, motor house, or cell maker. CP01 through CP34 are draft. Controlling process steps are P01 through P34. Capsule latch is P04. Radio-module hold is P18. DRONE-10 is a $60.00 labor estimate for HIL calibration, not a qualified lab. Year-1 commercial units authorized: 0. No outdoor flight is authorized. No award and no purchase order. Explanation: A capability claim for this product would have to cover composite, propulsion, cells, and a dock, not only a plastic tool. No such qualification is on file. Directory names and dated bids are not qualification. | Result (Y/N/NA): N Status: Open — no capability evidence | BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-CONTROL-PLAN-001 Rev C1 CP01 through CP34 draft; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1 33 bids, unawarded; CTQ25. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale requests no shop survey and no flight demonstration. No outdoor flight is authorized. The bids stay unawarded. Target 2027-06-15, planned. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. No audit, process limit, or production address is on file. Directory names are not qualification. |
Item ID: PRODUCTION-03 Question: What are the real costs and commitments? | Answer / assumption: No spending committed; tooling allowance $60,000.00; per-unit packed cost $740.00 estimate. Funding worksheet C1 states a $250,000.00 feasibility allowance, status Not funded/committed, type Owner Basic capital only, and future Hotel/Drone funding not secured. It says stop before the capsule tool and before any flight. The unfunded ceiling is ground rig $100,000.00, bench testing and welfare $75,000.00, engineering and market notes $50,000.00, and reserve $25,000.00. The $60,000.00 capsule allowance is outside that ceiling. Year-1 commercial units authorized: 0. BOM C1 puts the capsule tool on DRONE-18 as $60,000.00 NRE, already amortized at $200.00. Lines on BMT-DRONE-TEMPLATE-COST-SHEET-001 Rev C1: DRONE-01 Ventilated trap capsule line $213.00; DRONE-02 Wall deployment carriage line $50.00; DRONE-03 Guarded aircraft frame line $80.00; DRONE-04 Motors/ESC/prop set line $40.00, BOM qty 4 at $10.00 each; DRONE-05 Navigation and flight control line $105.00; DRONE-06 Redundant payload latch line $30.00; DRONE-07 Flight battery line $70.00; DRONE-08 Dock charger/interlocks line $45.00; DRONE-09 Radio/local gateway line $17.00; DRONE-10 Assembly/HIL calibration line $60.00; DRONE-11 Shipping crate/manual line $30.00. Running total $740.00. Shell amortization $200.00 on tooling $60,000.00 at 100 units/year for 3 years. BOM pre-tool sum $540.00. Adding the NRE mold row again would count the tool twice. BOM C1 states the amortized piece as $740.00. Ten times $740.00 is $7,400.00 of estimated packed cost, not a quote and not freight. DRONE-14 Remote ID equipment is $18.00 excluded, supplier Not selected, no RFQ, and is absent from DRONE-01 through DRONE-11. Adopting it would move the pre-tool sum from $540.00 to $558.00 and the piece from $740.00 to $758.00. Leave $740.00 until Jordan Vale closes CTQ26. The 100/year figure is a denominator. The RFQ quantity line records forecast sales as zero. Owner capital of $80,000.00 is not deposited. Explanation: The $60,000.00 capsule allowance sits outside the $250,000.00 ceiling. It is not a draw on the $100,000.00 ground-rig line, and a smaller number is not permission. The ceiling is not secured. The funding sheet stops before production tooling and before any flight. G1 holds tooling. | Result (Y/N/NA): N Status: Open — allowances uncommitted | BMT-DRONE-TEMPLATE-COST-SHEET-001 Rev C1 running total $740.00; BMT-DRONE-BOM-001 Rev C1 DRONE-14 and DRONE-18; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale leaves $740.00 and $60,000.00 uncommitted and does not move DRONE-14 into the piece. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Allowances are recorded and uncommitted. Nothing in this row is an awarded supplier price. The bids on DRONE-01 through DRONE-11 stay unawarded. |
Item ID: PRODUCTION-04 Question: Who owns tooling, data and changes? | Answer / assumption: Proposed company ownership of tooling/data; contract and ECN approval before later frozen changes. Tool owner is not one shared clause. FSW-D-2026-01 says the company owns the tool when paid. MPS-D-2026-02 says the shop keeps title until buyout. NLM-D-2026-03 says company title before kickoff, with the mold paid 100% before steel. No custody, maintenance, or removal clause is signed. BOM C1 DRONE-18 carries the mold note under Jordan Vale. Alex Meadow has not signed a contract. G3 is No freeze. DFM-06 bars a cell, antenna, propeller, or latch-sensor substitute unless the affected requirement is regressed. Lane Corwin has not cleared disclosure. The RFQ records no NDA and no disclosure. Explanation: Flight-article substitutions are design changes, not purchasing convenience. Nothing is frozen, and nothing has been disclosed under an NDA. | Result (Y/N/NA): N Status: Open — tool title unsigned | BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1; BMT-DRONE-BOM-001 Rev C1 DRONE-18; DFM-06; BMT-DRONE-RFQ-PACKAGE-001 Rev C1 NDA field. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale keeps tool title proposed. Alex Meadow is not asked to sign a clause that is not drafted. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Tool title is unsigned. The three bids do not share one title clause. No NDA and no change baseline. |
Item ID: PRODUCTION-05 Question: How will we accept incoming parts and production output? | Answer / assumption: Incoming configuration check, linked CP controls, planned FAI; no inspection evidence. Accept would use BOM C1 and draft controls CP01 through CP34, drawing revision Drone Trap C1, phase prototype. FAI characteristics are Not measured. Tests T01 through T34 are unrun. CTQ01 through CTQ34 are untested. Planned unit IDs DRONE-X1-001 onward have no results. The control plan names a fault-injection harness for the beam and the weight channel. It has not been built and it is not a production sample plan. Work instructions are draft. Controlling process steps are P01 through P34. Capsule latch is P04. Radio-module hold is P18. Field-release door is P25. Explanation: Incoming acceptance for a flight article would have to include retention, guards, energy reserve, and the dock. Those FAI rows are Not measured. No lot has been accepted. | Result (Y/N/NA): N Status: Blocked — FAI not measured | BMT-DRONE-CONTROL-PLAN-001 Rev C1 CP01 through CP34 draft; BMT-DRONE-TEMPLATE-FAI-REPORT-001 Rev C1 Not measured; unit IDs DRONE-X1-001. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale does not open FAI results and does not accept a ground fixture as a flight article. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. FAI characteristics are Not measured. Draft controls are not acceptance. |
Item ID: PRODUCTION-06 Question: Can we deliver and recover from interruption? | Answer / assumption: Assume single source initially; qualify backup before scale; no promised delivery. A 10-unit first article is not built. The 100-a-year figure is a cost case, not a forecast. Year-1 commercial units authorized: 0. Meadow Prototype Shop bids 10 a year, is not an aircraft qualification, and is not a qualified backup. Frame $80.00, motors $40.00, navigation $105.00, battery $70.00, and dock $45.00 have dated bids and lead times on DRONE-01 through DRONE-11. Those bids are unawarded and are not a delivery promise. G1 is Hold tooling pending evidence. No reorder point, no inventory, and no delivery promise. C1 authorizes no outdoor flight. Explanation: Interruption recovery for this product is not a second mold shop. The articles that would stop a build have unawarded budgetary bids and no qualified alternate. | Result (Y/N/NA): N Status: Open — no recovery source | BMT-DRONE-RFQ-PACKAGE-001 Rev C1 quantities; BMT-DRONE-BOM-001 Rev C1 DRONE-03, DRONE-04, DRONE-05, DRONE-07, DRONE-08; CTQ25. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale does not promise a delivery date and does not schedule outdoor flight. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The volume figure is a cost denominator. No delivery date is promised. |
Item ID: PRODUCTION-07 Question: What must be in place after sale? | Answer / assumption: Traceability, complaints, recall containment, returns and safe disposal required before sale. Traceability, complaints, recall containment, returns, and safe disposal are required before any sale, and none of those records exist. For this product the same gap covers the cell, the firmware identity, and an aircraft that is not allowed to fly. CTQ26 Remote ID applicability is unresolved, and DRONE-14 is not selected. The BMT-DRONE-STAGE-GATES-001 Rev C1 marks G5 as Drone research only, not a launch. Nia Calder has not bound coverage. No spares price and no incident record exist. Nothing has been sold. Explanation: After-sale readiness cannot lead the flight rules. G5 is Drone research only, and a fielded aircraft is not defined while CTQ26 is open. | Result (Y/N/NA): N Status: Blocked — after-sale records absent | CTQ26; BMT-DRONE-BOM-001 Rev C1 DRONE-14; BMT-DRONE-STAGE-GATES-001 Rev C1 G5. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale does not open a service or returns record for an aircraft that C1 does not allow to fly. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. After-sale records are absent. Gate G5 is not a launch. |
Item ID: PRODUCTION-08 Question: Is the first production order ready? | Answer / assumption: Not ready: no released drawings, supplier qualification, physical tests or reviewed controls. G0 through G5 are pending. None has occurred. G0 is planned for 2027-01-28. G3 is No freeze. G4 is No purchase order. Missing drawings, supplier qualification, physical tests, and reviewed controls each block an order. A capsule quote would not authorize a flight article. This row is not a release. Explanation: PRODUCTION-08 stops the sheet. Simulation and specialist review remain the prior step, and they are not done. No purchase order is inferred. | Result (Y/N/NA): N Status: Blocked — release not recorded | BMT-DRONE-STAGE-GATES-001 Rev C1 G0, G3, G4; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1 not secured. Dated 2026-10-24. | Owner: Jordan Vale Next action: Nobody places a production order. Do not read this sheet as flight authority. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. This row is the buy stop. It is not a release by Alex Meadow. |
Item ID: PRODUCTION-09 Question: Is one released revision ready so the quoted shops would be on the same released part? | Answer / assumption: Not ready. DFM-07 records requirements R01 through R30 at C1 and no released CAD or drawings. DFM-03 and DFM-04 remain open on draft, stack-up, and wash aging. DFM-08 records no manufacturer comments. CTQ26 is open, so the aircraft identity hardware is not in the package. Thirty-three bids are on file for DRONE-01 through DRONE-11 and are not one released revision. No drawing has been released. Explanation: Three quote contacts have bids, and those bids are not one released aircraft configuration. Remote ID is intentionally outside the piece until CTQ26 closes, which means the package is not one configuration. | Result (Y/N/NA): N Status: Blocked — drawing not released | DFM-07 and DFM-08; CTQ26; BMT-DRONE-BOM-001 Rev C1 DRONE-14; BMT-DRONE-RFQ-PACKAGE-001 Rev C1. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale lists open DFM rows and the CTQ26 exclusion on the held package and does not award it. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. No released drawing, so the bids on file are not one released part. |
Item ID: PRODUCTION-10 Question: Is every CTQ measurable on a first-article record with a defined gauge and sample? | Answer / assumption: Not measurable as a first article. FAI characteristics are Not measured. Tests T01 through T34 are unrun. The full set is CTQ01 through CTQ34. Suitability review on BMT-DRONE-CONTROL-PLAN-001 Rev C1 is pending. Limits that have no rig on file include CTQ18 two retention paths and a ground-contact switch, CTQ19 no rotor spin until guards are verified, CTQ21 a proposed return reserve of at least 40%, CTQ23 release only with motors stopped on a validated surface, CTQ25 no unattended outdoor launch, CTQ26 Remote ID unresolved, CTQ27 no charge after a failed dock alignment, CTQ28 dry air and wind below 3 m/s as a research envelope only, CTQ29 a signed mission plan, and CTQ30 one failed dock then a designated safe land. The sample line names a fault-injection rig that has not been built. No flight lab is named. Ira Bell is a latch-and-vent lab candidate on the people register and is not a flight lab, and he has not been contacted. Explanation: FAI for this product is the full CTQ01 through CTQ34 set, not a short mechanical index. The flight limits above are proposed acceptance text, not measured results, and C1 authorizes no outdoor flight in which to collect them. CTQ31 through CTQ34 cover capsule-tool drift, a short guard set, the 40% energy reserve while chemistry is unselected, and a crate read as permission to fly. | Result (Y/N/NA): N Status: Open — CTQ gauges not suitable | BMT-DRONE-CRITICAL-QUALITY-001 Rev C1 CTQ01 through CTQ34; BMT-DRONE-TEMPLATE-FAI-REPORT-001 Rev C1 Not measured; BMT-DRONE-CONTROL-PLAN-001 Rev C1 suitability pending. | Owner: Jordan Vale Next action: Jordan Vale does not book a flight lab. No flight lab is named, and none is authorized by this row. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Gauge suitability is pending. FAI stays Not measured. |
Item ID: PRODUCTION-11 Question: Is pilot cash identified, and is production tooling still stopped? | Answer / assumption: Identified only as an unfunded estimate. The $250,000.00 allowance is not secured. Future Hotel/Drone funding is not secured. The $100,000.00 ground-rig line has not been released. Ten times $740.00 is $7,400.00. That amount is not a purchase order. DRONE-18 at $60,000.00 stays stopped because that capsule allowance is outside the $250,000.00 ceiling, not because it is smaller than the ground-rig line. The company is not formed. Ellis Brook at Example Meadow Bank is a depository contact only. Credit is not requested. Owner capital of $80,000.00 is not deposited. Explanation: The capsule allowance is outside the unfunded ceiling. G1 holds tooling and G4 forbids the purchase order. G0 through G5 are pending. No flight is authorized. | Result (Y/N/NA): Y Status: Recorded — stop holds; cash unfunded | BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1 $250,000.00 not secured; BMT-DRONE-BOM-001 Rev C1 DRONE-18; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1 bank and capital. Dated 2026-10-24. | Owner: Jordan Vale Next action: Alex Meadow does not release prototype cash or the capsule mold. Jordan Vale records the stop. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The tooling stop holds. Pilot cash is an unfunded estimate, not a release. |
Item ID: PRODUCTION-12 Question: Are sub-tier parts and special processes identified to a named source? | Answer / assumption: No qualified sub-tier. Fictional Sample Works, Meadow Prototype Shop, and Fictional Northline Molding have unawarded bids on DRONE-01 through DRONE-11. A tooling bid is not a flight qualification. Included splits excluded from the $540.00 sum: DRONE-12 propeller guards qty 4, allowance $4.00 each; DRONE-13 payload coupler hardware allowance $8.00; DRONE-15 weather monitor allowance $8.00; DRONE-16 dock contact pair qty 2, allowance $3.50 each; DRONE-17 return-dock beacon allowance $4.00. DRONE-14 is the separate $18.00 exclusion, with no supplier selected. No composite shop, motor source, or cell maker is named. Cell watt-hours are unselected. DFM-06 bars a cell, antenna, propeller, or latch-sensor substitute without regression. Explanation: The $540.00 sum is a rollup of unnamed purchased articles plus included splits. It is not a source list. Pricing the splits again, or adding DRONE-14 without closing CTQ26, would break the piece. | Result (Y/N/NA): N Status: Open — sub-tier sources unnamed | BMT-DRONE-BOM-001 Rev C1 DRONE-12 through DRONE-17 and DRONE-14; DFM-06; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1 Perry Voss. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale leaves every sub-tier blank rather than invent a source. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Sub-tier sources are unnamed. Included splits must not be priced twice. |
Item ID: PRODUCTION-13 Question: Is the carton, the instruction revision, and the shipping trial defined for the packed unit? | Answer / assumption: Not defined. DRONE-11, the shipping crate and manual, is line $30.00 inside the $540.00 sum. The RFQ says a shipping qualification is planned and it has not been run. The protected lithium pack has no transport classification on file, and no shipment is authorized. Freight and duty are excluded on every bid, so freight is not a landed cost. Payment terms on the bids are not a signed contract. DRONE-14 is not in the crate cost. The $740.00 piece is not a landed cost. Explanation: A crate allowance is not a packaging qualification. The cell makes the gap material, and this sheet does not supply a shipping method. It records that the trial is absent. | Result (Y/N/NA): N Status: Open — pack and freight undefined | BMT-DRONE-BOM-001 Rev C1 DRONE-11 and DRONE-07; BMT-DRONE-RFQ-PACKAGE-001 Rev C1 packaging; quote comparison bid terms filled, freight excluded, and not signed as a contract. | Owner: Jordan Vale Next action: Jordan Vale marks freight, the shipping trial, and cell transport as open exclusions. No unit is shipped. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The instruction text is a bill-of-materials note. Freight is excluded on the bids and is not a landed cost. |
Item ID: PRODUCTION-14 Question: Can each packed unit be traced to component lots and the assembly record? | Answer / assumption: Not traceable. The control plan says: Planned unit IDs DRONE-X1-001 onward; no results There is no serial for the airframe, the cell, the motor set, or a firmware hash. CTQ29 requires a signed mission plan and there is no configuration record to sign. CTQ26 is unresolved, so an aircraft-identity record cannot be opened. DRONE-14 has no device selected. Explanation: Recall containment for a flight article needs the configuration, not only a plastic shot code. That record does not exist, which is why PRODUCTION-07 stays open. | Result (Y/N/NA): N Status: Open — traceability blank | BMT-DRONE-CONTROL-PLAN-001 Rev C1 traceability DRONE-X1-001; CTQ26 and CTQ29; BMT-DRONE-BOM-001 Rev C1 DRONE-14. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale does not assign an aircraft serial while CTQ26 is open. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Planned serials have no lot code, traveler, or retain. |
Item ID: PRODUCTION-15 Question: Which open process failures block acceptance of a pilot lot? | Answer / assumption: Do not accept a pilot lot or a flight article. BMT-DRONE-PFMEA-001 Rev C1 has 102 data rows, PF01 through PF99 (plus crate-close submodes PF99-A/PF99-B/PF99-C; 102 rows). Status is Open, Hold, or Blocked. No row is accepted. Severity 9 or 10 lines number 76. Highest lines include PF25 RPN 630 severity 10 (Route file still contains an unattended outdoor leg; Hold); PF20 RPN 450 severity 10 (Geofence slot loaded from the planner file; Open); PF18 RPN 400 severity 10 (Primary latch left short of seated; Open); PF19 RPN 350 severity 10 (Arm check signed with a rotor still reachable; Open); PF06 RPN 432 severity 9 (Window line signed with no pane check; Blocked); PF09 RPN 432 severity 9 (Station closed on a phone notification; Open); PF12 RPN 320 severity 10 (Thermal stop left out of the charge setup; Blocked); PF08 RPN 360 severity 9 (Weight channel left unwired while the beam still reads; Open); PF24 RPN 567 severity 9 (Empty registry signed as reviewed; Blocked); PF21 RPN 480 severity 10 (Reserve computed on a light payload and still air; Open); PF28 RPN 480 severity 10 (Missing-sensor case jumpered to a stored clear value; Open); PF30 RPN 480 severity 10 (Second approach left enabled; Open). Those highlighted lines do not stand in for the 102 data rows. Controls are CP01 through CP34, draft. Capsule latch is P04. Radio-module hold is P18. Field-release door is P25. CTQ01 through CTQ34 are untested. Tests T01 through T34 are unrun. Year-1 commercial units authorized: 0. Outdoor flight is not authorized. Explanation: These rows are the production block, not a flight procedure. While they stay unaccepted, G4 cannot move. C1 says outdoor flight is unauthorized. | Result (Y/N/NA): Y Status: Recorded — pilot lot refused | BMT-DRONE-PFMEA-001 Rev C1, 102 data rows PF01 through PF99 (plus crate-close submodes PF99-A/PF99-B/PF99-C; 102 rows), none accepted. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale keeps pilot quantity at zero and does not schedule a flight to close these rows. Target 2027-06-15, planned. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Open PFMEA rows stay unaccepted. A pilot lot is refused. RPN is unchanged. |
Item ID: PRODUCTION-16 Question: What has to be signed before an RFQ goes out or tool steel is cut? | Answer / assumption: Nothing is signed. The RFQ package still records no signed agreement and no disclosure. Bids on the comparison sheet do not close that gap. Lane Corwin is not engaged. Perry Voss, Willa Marsh, and Eden Crowe have bids on file. No award and no purchase order. Any later contract would also have to say that a supplier signature does not authorize outdoor flight, Remote ID equipment, or a cell shipment. Those clauses are not drafted. Steel is stopped under PRODUCTION-11. Explanation: The contract gap is wider than a mold PO. A normal tooling RFQ would not flow down CTQ25 or CTQ26, so the package is not ready to leave the company. | Result (Y/N/NA): N Status: Blocked — terms and NDA unsigned | BMT-DRONE-RFQ-PACKAGE-001 Rev C1 NDA field; CTQ25 and CTQ26; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1 Lane Corwin. Dated 2026-10-24. | Owner: Jordan Vale Next action: Jordan Vale holds the file. This row does not engage counsel and does not award a bid. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. No NDA, tool clause, or payment term is signed. The file stays in house. |
Item ID: PRODUCTION-17 Question: Are the capsule mold and the flight articles defined enough to buy? | Answer / assumption: No. DRONE-18 is the internal $60,000.00 capsule allowance, outside the $250,000.00 ceiling, not ordered, and not a supplier bid. It is already amortized at $200.00 per unit on the 100-unit, 3-year cost basis. DRONE-01 bids, unawarded: FSW-D-2026-01 (Fictional Sample Works, Perry Voss) dated 2026-10-02, valid through 2026-12-31, P20 capsule mold, 1 cavity, 200,000 shots, tooling $72,400.00, volume piece $11.80, annual qty 100, tool lead 18 weeks, tool owner: The Better Mouse Trap Co. when paid. MPS-D-2026-02 (Fictional Meadow Prototype Shop, Willa Marsh) dated 2026-10-06, valid through 2026-12-05, Aluminum capsule bridge mold, 1 cavity, 15,000 shots, tooling $22,500.00, volume piece $24.50, annual qty 10, tool lead 7 weeks, tool owner: Meadow Prototype Shop until buyout. NLM-D-2026-03 (Fictional Northline Molding, Eden Crowe) dated 2026-10-09, valid through 2027-01-07, Pre-hard capsule mold, 1 cavity, 120,000 shots, tooling $54,800.00, volume piece $14.20, annual qty 100, tool lead 15 weeks, tool owner: The Better Mouse Trap Co. before kickoff. DFM-02 says bridge process before a production tool at the 100-a-year cost case. Purchased lines have budgetary bids and no qualified source beyond those unawarded rows: frame $80.00, motors $40.00 (BOM qty 4 at $10.00 each), navigation $105.00, latch $30.00, battery $70.00, dock $45.00, radio $17.00. CTQ18, CTQ19, and CTQ27 are unproven. CTQ01 through CTQ34 are the full set. PF18 and PF27 stay unaccepted. The capsule dollar is not a draw on the $100,000.00 ground-rig line. Year-1 commercial units authorized: 0. Explanation: Buying the mold, the motors, or the cell from the cost sheet would skip qualification and would double count tooling that is already in the $740.00 piece. The $60,000.00 allowance is outside the $250,000.00 ceiling. No flight is authorized. | Result (Y/N/NA): N Status: Blocked — mold not released to cut | BMT-DRONE-BOM-001 Rev C1 DRONE-03 through DRONE-09 and DRONE-18; CTQ18, CTQ19, CTQ27, and CTQ01 through CTQ34; PF18 and PF27; quote comparison FSW-D-2026-01, MPS-D-2026-02, and | Owner: Jordan Vale Next action: Do not buy the mold, the motors, the cell, or the dock. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The mold is an allowance. Steel is not released. |
Item ID: PRODUCTION-18 Question: What blocks a first production order even with capsule bids on file? | Answer / assumption: Not ready: no released drawings, supplier qualification, physical tests or reviewed controls. Capsule bids on file are not an aircraft order and are not a flight release. Independent blocks: G4 No purchase order, G3 No freeze, Hotel/Drone funding not secured, DRONE-18 stopped, FAI Not measured, CP01 through CP34 draft on process steps P01 through P34, radio-module hold at P18, the severity 10 process rows still unaccepted, CTQ21 reserve still a proposal, CTQ25 no unattended outdoor launch, CTQ26 open so the piece stays $740.00 rather than $758.00, CTQ28 not a validated wind limit, no named flight reviewer, no formed company, and no bank account. C1 authorizes no outdoor flight. Explanation: This is the order gate for a bank reader. The rest of the sheet can be complete as a checklist and the order is still unplaced. G0 through G5 are pending. None has occurred. G0 is planned for 2027-01-28. | Result (Y/N/NA): Y Status: Recorded — order stays unplaced | BMT-DRONE-STAGE-GATES-001 Rev C1 G0, G3, G4; CTQ21, CTQ25, CTQ26, CTQ28; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1. Dated 2026-10-24. | Owner: Jordan Vale Next action: Leave the order unplaced. Do not treat a capsule quote as authority to fly. Target 2027-06-15. Reviewer / review date: Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The blocks are independent. A later quote does not place the order. |
Drone Trap — Suppliers and Production Readiness — supporting detail
Drone Trap — Are all suppliers quoting the same thing?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-01
Question. Are all suppliers quoting the same thing?
Evidence to record. Exact revision/material/finish/quantities, inspection, packaging and acceptance requirements; assumptions and exclusions alongside each quote.
Result (Y/N/NA). N
Explanation. G1 is Hold tooling pending evidence. Thirty-three unawarded bids do not create a flight supplier and do not authorize outdoor flight. A reader who treats $740.00 or the $60,000.00 allowance as an awarded price is reading the cost sheet. Year-1 commercial units authorized: 0.
Status. Open — bids unawarded, drawing not released
Evidence / exact revision / URL and date. BMT-DRONE-BOM-001 Rev C1 DRONE-01 through DRONE-18; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1, 33 dated bids, FSW-D-2026-01 through NLM-D-2026-33, unawarded. Recorded 2026-10-24. The Casey Holt read is planned for 2026-11-01 and has not been held.
Owner. Jordan Vale
Next action. Jordan Vale does not award a bid and does not imply a flight shop from the quote contacts. No purchase order. Target 2027-06-15, planned.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Thirty-three bids stay unawarded. There is no common released offer and no purchase order.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1; BMT-DRONE-RFQ-PACKAGE-001 Rev C1
Drone Trap — Can the supplier actually make and inspect it?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-02
Question. Can the supplier actually make and inspect it?
Evidence to record. Relevant capabilities, process limits, capacity, sample evidence, documented process scope, references, subcontractors and production location. Directory membership alone is not qualification.
Answer / assumption. No audit or capability study. The thirty-three bids are not an audit. No process limit, sample, quality-system scope, or production address is on file beyond the quote rows. Perry Voss, Willa Marsh, and Eden Crowe are quote contacts on DRONE-01 through DRONE-11. Those bids do not show a qualified composite shop, motor house, or cell maker. CP01 through CP34 are draft. Controlling process steps are P01 through P34. Capsule latch is P04. Radio-module hold is P18. DRONE-10 is a $60.00 labor estimate for HIL calibration, not a qualified lab. Year-1 commercial units authorized: 0. No outdoor flight is authorized. No award and no purchase order.
Result (Y/N/NA). N
Explanation. A capability claim for this product would have to cover composite, propulsion, cells, and a dock, not only a plastic tool. No such qualification is on file. Directory names and dated bids are not qualification.
Status. Open — no capability evidence
Evidence / exact revision / URL and date. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-CONTROL-PLAN-001 Rev C1 CP01 through CP34 draft; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1 33 bids, unawarded; CTQ25. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale requests no shop survey and no flight demonstration. No outdoor flight is authorized. The bids stay unawarded. Target 2027-06-15, planned.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. No audit, process limit, or production address is on file. Directory names are not qualification.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-CONTROL-PLAN-001 Rev C1; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1
Drone Trap — What are the real costs and commitments?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-03
Question. What are the real costs and commitments?
Evidence to record. Unit prices at realistic volumes, tooling/NRE, MOQ, lead times, payment/deposit terms, currency, freight/trade terms, duties, scrap, quote expiry and cancellation/change terms.
Answer / assumption. No spending committed; tooling allowance $60,000.00; per-unit packed cost $740.00 estimate. Funding worksheet C1 states a $250,000.00 feasibility allowance, status Not funded/committed, type Owner Basic capital only, and future Hotel/Drone funding not secured. It says stop before the capsule tool and before any flight. The unfunded ceiling is ground rig $100,000.00, bench testing and welfare $75,000.00, engineering and market notes $50,000.00, and reserve $25,000.00. The $60,000.00 capsule allowance is outside that ceiling. Year-1 commercial units authorized: 0. BOM C1 puts the capsule tool on DRONE-18 as $60,000.00 NRE, already amortized at $200.00. Lines on BMT-DRONE-TEMPLATE-COST-SHEET-001 Rev C1: DRONE-01 Ventilated trap capsule line $213.00; DRONE-02 Wall deployment carriage line $50.00; DRONE-03 Guarded aircraft frame line $80.00; DRONE-04 Motors/ESC/prop set line $40.00, BOM qty 4 at $10.00 each; DRONE-05 Navigation and flight control line $105.00; DRONE-06 Redundant payload latch line $30.00; DRONE-07 Flight battery line $70.00; DRONE-08 Dock charger/interlocks line $45.00; DRONE-09 Radio/local gateway line $17.00; DRONE-10 Assembly/HIL calibration line $60.00; DRONE-11 Shipping crate/manual line $30.00. Running total $740.00. Shell amortization $200.00 on tooling $60,000.00 at 100 units/year for 3 years. BOM pre-tool sum $540.00. Adding the NRE mold row again would count the tool twice. BOM C1 states the amortized piece as $740.00. Ten times $740.00 is $7,400.00 of estimated packed cost, not a quote and not freight. DRONE-14 Remote ID equipment is $18.00 excluded, supplier Not selected, no RFQ, and is absent from DRONE-01 through DRONE-11. Adopting it would move the pre-tool sum from $540.00 to $558.00 and the piece from $740.00 to $758.00. Leave $740.00 until Jordan Vale closes CTQ26. The 100/year figure is a denominator. The RFQ quantity line records forecast sales as zero. Owner capital of $80,000.00 is not deposited.
Result (Y/N/NA). N
Explanation. The $60,000.00 capsule allowance sits outside the $250,000.00 ceiling. It is not a draw on the $100,000.00 ground-rig line, and a smaller number is not permission. The ceiling is not secured. The funding sheet stops before production tooling and before any flight. G1 holds tooling.
Status. Open — allowances uncommitted
Evidence / exact revision / URL and date. BMT-DRONE-TEMPLATE-COST-SHEET-001 Rev C1 running total $740.00; BMT-DRONE-BOM-001 Rev C1 DRONE-14 and DRONE-18; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale leaves $740.00 and $60,000.00 uncommitted and does not move DRONE-14 into the piece. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Allowances are recorded and uncommitted. Nothing in this row is an awarded supplier price. The bids on DRONE-01 through DRONE-11 stay unawarded.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-TEMPLATE-COST-SHEET-001 Rev C1; BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1
Drone Trap — Who owns tooling, data and changes?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-04
Question. Who owns tooling, data and changes?
Evidence to record. Tool ownership, custody, maintenance and transfer access; drawings and IP, approved substitutions and who can authorize changes.
Answer / assumption. Proposed company ownership of tooling/data; contract and ECN approval before later frozen changes. Tool owner is not one shared clause. FSW-D-2026-01 says the company owns the tool when paid. MPS-D-2026-02 says the shop keeps title until buyout. NLM-D-2026-03 says company title before kickoff, with the mold paid 100% before steel. No custody, maintenance, or removal clause is signed. BOM C1 DRONE-18 carries the mold note under Jordan Vale. Alex Meadow has not signed a contract. G3 is No freeze. DFM-06 bars a cell, antenna, propeller, or latch-sensor substitute unless the affected requirement is regressed. Lane Corwin has not cleared disclosure. The RFQ records no NDA and no disclosure.
Result (Y/N/NA). N
Explanation. Flight-article substitutions are design changes, not purchasing convenience. Nothing is frozen, and nothing has been disclosed under an NDA.
Status. Open — tool title unsigned
Evidence / exact revision / URL and date. BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1; BMT-DRONE-BOM-001 Rev C1 DRONE-18; DFM-06; BMT-DRONE-RFQ-PACKAGE-001 Rev C1 NDA field. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale keeps tool title proposed. Alex Meadow is not asked to sign a clause that is not drafted. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Tool title is unsigned. The three bids do not share one title clause. No NDA and no change baseline.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1; BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-RFQ-PACKAGE-001 Rev C1
Drone Trap — How will we accept incoming parts and production output?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-05
Question. How will we accept incoming parts and production output?
Evidence to record. First-article/pilot evidence, critical characteristics, sampling rationale, measurement methods, traceability, nonconformance/rework and corrective actions.
Answer / assumption. Incoming configuration check, linked CP controls, planned FAI; no inspection evidence. Accept would use BOM C1 and draft controls CP01 through CP34, drawing revision Drone Trap C1, phase prototype. FAI characteristics are Not measured. Tests T01 through T34 are unrun. CTQ01 through CTQ34 are untested. Planned unit IDs DRONE-X1-001 onward have no results. The control plan names a fault-injection harness for the beam and the weight channel. It has not been built and it is not a production sample plan. Work instructions are draft. Controlling process steps are P01 through P34. Capsule latch is P04. Radio-module hold is P18. Field-release door is P25.
Result (Y/N/NA). N
Explanation. Incoming acceptance for a flight article would have to include retention, guards, energy reserve, and the dock. Those FAI rows are Not measured. No lot has been accepted.
Status. Blocked — FAI not measured
Evidence / exact revision / URL and date. BMT-DRONE-CONTROL-PLAN-001 Rev C1 CP01 through CP34 draft; BMT-DRONE-TEMPLATE-FAI-REPORT-001 Rev C1 Not measured; unit IDs DRONE-X1-001. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale does not open FAI results and does not accept a ground fixture as a flight article. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. FAI characteristics are Not measured. Draft controls are not acceptance.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-CONTROL-PLAN-001 Rev C1; BMT-DRONE-TEMPLATE-FAI-REPORT-001 Rev C1; BMT-DRONE-WORK-INSTRUCTIONS-001 Rev C1
Drone Trap — Can we deliver and recover from interruption?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-06
Question. Can we deliver and recover from interruption?
Evidence to record. Pilot quantity, ramp/capacity plan, long-lead parts, approved alternate sources, packaging/shipping trials, inventory and reorder points.
Answer / assumption. Assume single source initially; qualify backup before scale; no promised delivery. A 10-unit first article is not built. The 100-a-year figure is a cost case, not a forecast. Year-1 commercial units authorized: 0. Meadow Prototype Shop bids 10 a year, is not an aircraft qualification, and is not a qualified backup. Frame $80.00, motors $40.00, navigation $105.00, battery $70.00, and dock $45.00 have dated bids and lead times on DRONE-01 through DRONE-11. Those bids are unawarded and are not a delivery promise. G1 is Hold tooling pending evidence. No reorder point, no inventory, and no delivery promise. C1 authorizes no outdoor flight.
Result (Y/N/NA). N
Explanation. Interruption recovery for this product is not a second mold shop. The articles that would stop a build have unawarded budgetary bids and no qualified alternate.
Status. Open — no recovery source
Evidence / exact revision / URL and date. BMT-DRONE-RFQ-PACKAGE-001 Rev C1 quantities; BMT-DRONE-BOM-001 Rev C1 DRONE-03, DRONE-04, DRONE-05, DRONE-07, DRONE-08; CTQ25. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale does not promise a delivery date and does not schedule outdoor flight. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The volume figure is a cost denominator. No delivery date is promised.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-RFQ-PACKAGE-001 Rev C1; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1
Drone Trap — What must be in place after sale?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-07
Question. What must be in place after sale?
Evidence to record. Warranty, spare parts, service, complaints, traceability and recall/incident process appropriate to product/market.
Answer / assumption. Traceability, complaints, recall containment, returns and safe disposal required before sale. Traceability, complaints, recall containment, returns, and safe disposal are required before any sale, and none of those records exist. For this product the same gap covers the cell, the firmware identity, and an aircraft that is not allowed to fly. CTQ26 Remote ID applicability is unresolved, and DRONE-14 is not selected. The BMT-DRONE-STAGE-GATES-001 Rev C1 marks G5 as Drone research only, not a launch. Nia Calder has not bound coverage. No spares price and no incident record exist. Nothing has been sold.
Result (Y/N/NA). N
Explanation. After-sale readiness cannot lead the flight rules. G5 is Drone research only, and a fielded aircraft is not defined while CTQ26 is open.
Status. Blocked — after-sale records absent
Evidence / exact revision / URL and date. CTQ26; BMT-DRONE-BOM-001 Rev C1 DRONE-14; BMT-DRONE-STAGE-GATES-001 Rev C1 G5. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale does not open a service or returns record for an aircraft that C1 does not allow to fly. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. After-sale records are absent. Gate G5 is not a launch.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-STAGE-GATES-001 Rev C1; BMT-DRONE-CRITICAL-QUALITY-001 Rev C1
Drone Trap — Is the first production order ready?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-08
Question. Is the first production order ready?
Evidence to record. Close or explicitly disposition DFM/test gaps, confirm current file package and cash need with the funding role. Record the person’s release decision; never infer authorization to place an order.
Answer / assumption. Not ready: no released drawings, supplier qualification, physical tests or reviewed controls. G0 through G5 are pending. None has occurred. G0 is planned for 2027-01-28. G3 is No freeze. G4 is No purchase order. Missing drawings, supplier qualification, physical tests, and reviewed controls each block an order. A capsule quote would not authorize a flight article. This row is not a release.
Result (Y/N/NA). N
Explanation. PRODUCTION-08 stops the sheet. Simulation and specialist review remain the prior step, and they are not done. No purchase order is inferred.
Status. Blocked — release not recorded
Evidence / exact revision / URL and date. BMT-DRONE-STAGE-GATES-001 Rev C1 G0, G3, G4; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1 not secured. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Nobody places a production order. Do not read this sheet as flight authority. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. This row is the buy stop. It is not a release by Alex Meadow.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-STAGE-GATES-001 Rev C1; BMT-DRONE-CHECK-SHEET-DFM-001 Rev C1; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1
Drone Trap — Is one released revision ready so the quoted shops would be on the same released part?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-09
Question. Is one released revision ready so the quoted shops would be on the same released part?
Evidence to record. Released drawing revision, BOM revision, material and finish for capsule and flight articles, quantities, inspection, packaging, exclusions, and a DFM disposition, as one package.
Answer / assumption. Not ready. DFM-07 records requirements R01 through R30 at C1 and no released CAD or drawings. DFM-03 and DFM-04 remain open on draft, stack-up, and wash aging. DFM-08 records no manufacturer comments. CTQ26 is open, so the aircraft identity hardware is not in the package. Thirty-three bids are on file for DRONE-01 through DRONE-11 and are not one released revision. No drawing has been released.
Result (Y/N/NA). N
Explanation. Three quote contacts have bids, and those bids are not one released aircraft configuration. Remote ID is intentionally outside the piece until CTQ26 closes, which means the package is not one configuration.
Status. Blocked — drawing not released
Evidence / exact revision / URL and date. DFM-07 and DFM-08; CTQ26; BMT-DRONE-BOM-001 Rev C1 DRONE-14; BMT-DRONE-RFQ-PACKAGE-001 Rev C1. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale lists open DFM rows and the CTQ26 exclusion on the held package and does not award it. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. No released drawing, so the bids on file are not one released part.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-CHECK-SHEET-DFM-001 Rev C1; BMT-DRONE-RFQ-PACKAGE-001 Rev C1
Drone Trap — Is every CTQ measurable on a first-article record with a defined gauge and sample?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-10
Question. Is every CTQ measurable on a first-article record with a defined gauge and sample?
Evidence to record. For each of CTQ01 through CTQ34: gauge or rig identity, calibration or configuration date, method, sample, and the FAI row. Mark flight limits that are still proposals.
Answer / assumption. Not measurable as a first article. FAI characteristics are Not measured. Tests T01 through T34 are unrun. The full set is CTQ01 through CTQ34. Suitability review on BMT-DRONE-CONTROL-PLAN-001 Rev C1 is pending. Limits that have no rig on file include CTQ18 two retention paths and a ground-contact switch, CTQ19 no rotor spin until guards are verified, CTQ21 a proposed return reserve of at least 40%, CTQ23 release only with motors stopped on a validated surface, CTQ25 no unattended outdoor launch, CTQ26 Remote ID unresolved, CTQ27 no charge after a failed dock alignment, CTQ28 dry air and wind below 3 m/s as a research envelope only, CTQ29 a signed mission plan, and CTQ30 one failed dock then a designated safe land. The sample line names a fault-injection rig that has not been built. No flight lab is named. Ira Bell is a latch-and-vent lab candidate on the people register and is not a flight lab, and he has not been contacted.
Result (Y/N/NA). N
Explanation. FAI for this product is the full CTQ01 through CTQ34 set, not a short mechanical index. The flight limits above are proposed acceptance text, not measured results, and C1 authorizes no outdoor flight in which to collect them. CTQ31 through CTQ34 cover capsule-tool drift, a short guard set, the 40% energy reserve while chemistry is unselected, and a crate read as permission to fly.
Status. Open — CTQ gauges not suitable
Evidence / exact revision / URL and date. BMT-DRONE-CRITICAL-QUALITY-001 Rev C1 CTQ01 through CTQ34; BMT-DRONE-TEMPLATE-FAI-REPORT-001 Rev C1 Not measured; BMT-DRONE-CONTROL-PLAN-001 Rev C1 suitability pending. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale does not book a flight lab. No flight lab is named, and none is authorized by this row. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Gauge suitability is pending. FAI stays Not measured.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-CRITICAL-QUALITY-001 Rev C1; BMT-DRONE-TEMPLATE-FAI-REPORT-001 Rev C1; BMT-DRONE-CONTROL-PLAN-001 Rev C1; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1
Drone Trap — Is pilot cash identified, and is production tooling still stopped?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-11
Question. Is pilot cash identified, and is production tooling still stopped?
Evidence to record. Funded amount, the line it would use, the tool and the Remote ID allowance excluded from that line, the signer, and the hold gate.
Answer / assumption. Identified only as an unfunded estimate. The $250,000.00 allowance is not secured. Future Hotel/Drone funding is not secured. The $100,000.00 ground-rig line has not been released. Ten times $740.00 is $7,400.00. That amount is not a purchase order. DRONE-18 at $60,000.00 stays stopped because that capsule allowance is outside the $250,000.00 ceiling, not because it is smaller than the ground-rig line. The company is not formed. Ellis Brook at Example Meadow Bank is a depository contact only. Credit is not requested. Owner capital of $80,000.00 is not deposited.
Result (Y/N/NA). Y
Explanation. The capsule allowance is outside the unfunded ceiling. G1 holds tooling and G4 forbids the purchase order. G0 through G5 are pending. No flight is authorized.
Status. Recorded — stop holds; cash unfunded
Evidence / exact revision / URL and date. BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1 $250,000.00 not secured; BMT-DRONE-BOM-001 Rev C1 DRONE-18; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1 bank and capital. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Alex Meadow does not release prototype cash or the capsule mold. Jordan Vale records the stop. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The tooling stop holds. Pilot cash is an unfunded estimate, not a release.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1; BMT-DRONE-BOM-001 Rev C1; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1
Drone Trap — Are sub-tier parts and special processes identified to a named source?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-12
Question. Are sub-tier parts and special processes identified to a named source?
Evidence to record. For frame, guards, motors, navigation, latch, cell, dock, radio, and Remote ID: source name, spec, and contacted or not. State cost already inside a parent line.
Answer / assumption. No qualified sub-tier. Fictional Sample Works, Meadow Prototype Shop, and Fictional Northline Molding have unawarded bids on DRONE-01 through DRONE-11. A tooling bid is not a flight qualification. Included splits excluded from the $540.00 sum: DRONE-12 propeller guards qty 4, allowance $4.00 each; DRONE-13 payload coupler hardware allowance $8.00; DRONE-15 weather monitor allowance $8.00; DRONE-16 dock contact pair qty 2, allowance $3.50 each; DRONE-17 return-dock beacon allowance $4.00. DRONE-14 is the separate $18.00 exclusion, with no supplier selected. No composite shop, motor source, or cell maker is named. Cell watt-hours are unselected. DFM-06 bars a cell, antenna, propeller, or latch-sensor substitute without regression.
Result (Y/N/NA). N
Explanation. The $540.00 sum is a rollup of unnamed purchased articles plus included splits. It is not a source list. Pricing the splits again, or adding DRONE-14 without closing CTQ26, would break the piece.
Status. Open — sub-tier sources unnamed
Evidence / exact revision / URL and date. BMT-DRONE-BOM-001 Rev C1 DRONE-12 through DRONE-17 and DRONE-14; DFM-06; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1 Perry Voss. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale leaves every sub-tier blank rather than invent a source. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Sub-tier sources are unnamed. Included splits must not be priced twice.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-CHECK-SHEET-DFM-001 Rev C1
Drone Trap — Is the carton, the instruction revision, and the shipping trial defined for the packed unit?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-13
Question. Is the carton, the instruction revision, and the shipping trial defined for the packed unit?
Evidence to record. Crate spec, manual revision, transit trial, freight term, and the statement that cell transport classification is unresolved. Do not treat this row as shipping instructions.
Answer / assumption. Not defined. DRONE-11, the shipping crate and manual, is line $30.00 inside the $540.00 sum. The RFQ says a shipping qualification is planned and it has not been run. The protected lithium pack has no transport classification on file, and no shipment is authorized. Freight and duty are excluded on every bid, so freight is not a landed cost. Payment terms on the bids are not a signed contract. DRONE-14 is not in the crate cost. The $740.00 piece is not a landed cost.
Result (Y/N/NA). N
Explanation. A crate allowance is not a packaging qualification. The cell makes the gap material, and this sheet does not supply a shipping method. It records that the trial is absent.
Status. Open — pack and freight undefined
Evidence / exact revision / URL and date. BMT-DRONE-BOM-001 Rev C1 DRONE-11 and DRONE-07; BMT-DRONE-RFQ-PACKAGE-001 Rev C1 packaging; quote comparison bid terms filled, freight excluded, and not signed as a contract. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale marks freight, the shipping trial, and cell transport as open exclusions. No unit is shipped. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The instruction text is a bill-of-materials note. Freight is excluded on the bids and is not a landed cost.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-RFQ-PACKAGE-001 Rev C1; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1
Drone Trap — Can each packed unit be traced to component lots and the assembly record?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-14
Question. Can each packed unit be traced to component lots and the assembly record?
Evidence to record. Airframe serial, cell lot, motor set, firmware identity, Remote ID status, traveler, and retain rule.
Answer / assumption. Not traceable. The control plan says: Planned unit IDs DRONE-X1-001 onward; no results There is no serial for the airframe, the cell, the motor set, or a firmware hash. CTQ29 requires a signed mission plan and there is no configuration record to sign. CTQ26 is unresolved, so an aircraft-identity record cannot be opened. DRONE-14 has no device selected.
Result (Y/N/NA). N
Explanation. Recall containment for a flight article needs the configuration, not only a plastic shot code. That record does not exist, which is why PRODUCTION-07 stays open.
Status. Open — traceability blank
Evidence / exact revision / URL and date. BMT-DRONE-CONTROL-PLAN-001 Rev C1 traceability DRONE-X1-001; CTQ26 and CTQ29; BMT-DRONE-BOM-001 Rev C1 DRONE-14. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale does not assign an aircraft serial while CTQ26 is open. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Planned serials have no lot code, traveler, or retain.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-CONTROL-PLAN-001 Rev C1; BMT-DRONE-BOM-001 Rev C1
Drone Trap — Which open process failures block acceptance of a pilot lot?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-15
Question. Which open process failures block acceptance of a pilot lot?
Evidence to record. Each of the 102 process-FMEA rows, its RPN and severity, and the control that would have to catch it. None is accepted. This is not a flight procedure.
Answer / assumption. Do not accept a pilot lot or a flight article. BMT-DRONE-PFMEA-001 Rev C1 has 102 data rows, PF01 through PF99 (plus crate-close submodes PF99-A/PF99-B/PF99-C; 102 rows). Status is Open, Hold, or Blocked. No row is accepted. Severity 9 or 10 lines number 76. Highest lines include PF25 RPN 630 severity 10 (Route file still contains an unattended outdoor leg; Hold); PF20 RPN 450 severity 10 (Geofence slot loaded from the planner file; Open); PF18 RPN 400 severity 10 (Primary latch left short of seated; Open); PF19 RPN 350 severity 10 (Arm check signed with a rotor still reachable; Open); PF06 RPN 432 severity 9 (Window line signed with no pane check; Blocked); PF09 RPN 432 severity 9 (Station closed on a phone notification; Open); PF12 RPN 320 severity 10 (Thermal stop left out of the charge setup; Blocked); PF08 RPN 360 severity 9 (Weight channel left unwired while the beam still reads; Open); PF24 RPN 567 severity 9 (Empty registry signed as reviewed; Blocked); PF21 RPN 480 severity 10 (Reserve computed on a light payload and still air; Open); PF28 RPN 480 severity 10 (Missing-sensor case jumpered to a stored clear value; Open); PF30 RPN 480 severity 10 (Second approach left enabled; Open). Those highlighted lines do not stand in for the 102 data rows. Controls are CP01 through CP34, draft. Capsule latch is P04. Radio-module hold is P18. Field-release door is P25. CTQ01 through CTQ34 are untested. Tests T01 through T34 are unrun. Year-1 commercial units authorized: 0. Outdoor flight is not authorized.
Result (Y/N/NA). Y
Explanation. These rows are the production block, not a flight procedure. While they stay unaccepted, G4 cannot move. C1 says outdoor flight is unauthorized.
Status. Recorded — pilot lot refused
Evidence / exact revision / URL and date. BMT-DRONE-PFMEA-001 Rev C1, 102 data rows PF01 through PF99 (plus crate-close submodes PF99-A/PF99-B/PF99-C; 102 rows), none accepted. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale keeps pilot quantity at zero and does not schedule a flight to close these rows. Target 2027-06-15, planned.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. Open PFMEA rows stay unaccepted. A pilot lot is refused. RPN is unchanged.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-PFMEA-001 Rev C1; BMT-DRONE-CONTROL-PLAN-001 Rev C1
Drone Trap — What has to be signed before an RFQ goes out or tool steel is cut?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-16
Question. What has to be signed before an RFQ goes out or tool steel is cut?
Evidence to record. NDA, tool title and removal, change notice, payment, cancellation, expiry, gauge and FAI inclusions, warranty, scrap, flow-down that the contract does not authorize outdoor flight, and a line that a named shop is not qualified.
Answer / assumption. Nothing is signed. The RFQ package still records no signed agreement and no disclosure. Bids on the comparison sheet do not close that gap. Lane Corwin is not engaged. Perry Voss, Willa Marsh, and Eden Crowe have bids on file. No award and no purchase order. Any later contract would also have to say that a supplier signature does not authorize outdoor flight, Remote ID equipment, or a cell shipment. Those clauses are not drafted. Steel is stopped under PRODUCTION-11.
Result (Y/N/NA). N
Explanation. The contract gap is wider than a mold PO. A normal tooling RFQ would not flow down CTQ25 or CTQ26, so the package is not ready to leave the company.
Status. Blocked — terms and NDA unsigned
Evidence / exact revision / URL and date. BMT-DRONE-RFQ-PACKAGE-001 Rev C1 NDA field; CTQ25 and CTQ26; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1 Lane Corwin. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Jordan Vale holds the file. This row does not engage counsel and does not award a bid. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. No NDA, tool clause, or payment term is signed. The file stays in house.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-RFQ-PACKAGE-001 Rev C1; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1; BMT-COMPANY-TEMPLATE-PEOPLE-001 Rev C1
Drone Trap — Are the capsule mold and the flight articles defined enough to buy?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-17
Question. Are the capsule mold and the flight articles defined enough to buy?
Evidence to record. Mold cavity, tool life, and T0/T1 status, plus a named source for frame, motors, navigation, cell, dock, and radio. Record that numeric fit under the prototype line is not a release.
Answer / assumption. No. DRONE-18 is the internal $60,000.00 capsule allowance, outside the $250,000.00 ceiling, not ordered, and not a supplier bid. It is already amortized at $200.00 per unit on the 100-unit, 3-year cost basis. DRONE-01 bids, unawarded: FSW-D-2026-01 (Fictional Sample Works, Perry Voss) dated 2026-10-02, valid through 2026-12-31, P20 capsule mold, 1 cavity, 200,000 shots, tooling $72,400.00, volume piece $11.80, annual qty 100, tool lead 18 weeks, tool owner: The Better Mouse Trap Co. when paid. MPS-D-2026-02 (Fictional Meadow Prototype Shop, Willa Marsh) dated 2026-10-06, valid through 2026-12-05, Aluminum capsule bridge mold, 1 cavity, 15,000 shots, tooling $22,500.00, volume piece $24.50, annual qty 10, tool lead 7 weeks, tool owner: Meadow Prototype Shop until buyout. NLM-D-2026-03 (Fictional Northline Molding, Eden Crowe) dated 2026-10-09, valid through 2027-01-07, Pre-hard capsule mold, 1 cavity, 120,000 shots, tooling $54,800.00, volume piece $14.20, annual qty 100, tool lead 15 weeks, tool owner: The Better Mouse Trap Co. before kickoff. DFM-02 says bridge process before a production tool at the 100-a-year cost case. Purchased lines have budgetary bids and no qualified source beyond those unawarded rows: frame $80.00, motors $40.00 (BOM qty 4 at $10.00 each), navigation $105.00, latch $30.00, battery $70.00, dock $45.00, radio $17.00. CTQ18, CTQ19, and CTQ27 are unproven. CTQ01 through CTQ34 are the full set. PF18 and PF27 stay unaccepted. The capsule dollar is not a draw on the $100,000.00 ground-rig line. Year-1 commercial units authorized: 0.
Result (Y/N/NA). N
Explanation. Buying the mold, the motors, or the cell from the cost sheet would skip qualification and would double count tooling that is already in the $740.00 piece. The $60,000.00 allowance is outside the $250,000.00 ceiling. No flight is authorized.
Status. Blocked — mold not released to cut
Evidence / exact revision / URL and date. BMT-DRONE-BOM-001 Rev C1 DRONE-03 through DRONE-09 and DRONE-18; CTQ18, CTQ19, CTQ27, and CTQ01 through CTQ34; PF18 and PF27; quote comparison FSW-D-2026-01, MPS-D-2026-02, and NLM-D-2026-03, unawarded. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Do not buy the mold, the motors, the cell, or the dock. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The mold is an allowance. Steel is not released.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-BOM-001 Rev C1; BMT-DRONE-TEMPLATE-COST-SHEET-001 Rev C1; BMT-DRONE-CHECK-SHEET-DFM-001 Rev C1; BMT-DRONE-TEMPLATE-QUOTE-COMPARISON-001 Rev C1
Drone Trap — What blocks a first production order even with capsule bids on file?
Project. Drone Trap
Product revision. C1
Sheet revision. 1
Prepared by. Jordan Vale
Date. 2026-10-24
Target market / jurisdiction. U.S. adults; Wisconsin illustrative base
Decision being prepared. Next private feasibility gate
Sheet. Suppliers and Production Readiness
Lead. Jordan Vale
Item ID. PRODUCTION-18
Question. What blocks a first production order even with capsule bids on file?
Evidence to record. The PRODUCTION-08 release record, the open severity 10 process rows, the flight limits that are still proposals, and the unsecured allowance.
Answer / assumption. Not ready: no released drawings, supplier qualification, physical tests or reviewed controls. Capsule bids on file are not an aircraft order and are not a flight release. Independent blocks: G4 No purchase order, G3 No freeze, Hotel/Drone funding not secured, DRONE-18 stopped, FAI Not measured, CP01 through CP34 draft on process steps P01 through P34, radio-module hold at P18, the severity 10 process rows still unaccepted, CTQ21 reserve still a proposal, CTQ25 no unattended outdoor launch, CTQ26 open so the piece stays $740.00 rather than $758.00, CTQ28 not a validated wind limit, no named flight reviewer, no formed company, and no bank account. C1 authorizes no outdoor flight.
Result (Y/N/NA). Y
Explanation. This is the order gate for a bank reader. The rest of the sheet can be complete as a checklist and the order is still unplaced. G0 through G5 are pending. None has occurred. G0 is planned for 2027-01-28.
Status. Recorded — order stays unplaced
Evidence / exact revision / URL and date. BMT-DRONE-STAGE-GATES-001 Rev C1 G0, G3, G4; CTQ21, CTQ25, CTQ26, CTQ28; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1. Dated 2026-10-24.
Owner. Jordan Vale
Next action. Leave the order unplaced. Do not treat a capsule quote as authority to fly. Target 2027-06-15.
Reviewer / review date. Casey Holt review planned 2026-11-01, pending as of 2026-10-28, and not held. The blocks are independent. A later quote does not place the order.
Not-applicable reason. Applicable
Source guidance URLs. BMT-DRONE-STAGE-GATES-001 Rev C1; BMT-DRONE-FUNDING-WORKSHEET-001 Rev C1
Document administration
Scope. DRONE-C1 supplier readiness for the capsule and the buy-item airframe. Planned serials DRONE-X1-001 through DRONE-X1-010 are not built. No flight article. Thirty-three dated bids, FSW-D-2026-01 through NLM-D-2026-33, are unawarded. No purchase order. The $60,000.00 capsule allowance sits outside the $250,000.00 research ceiling. The ceiling is unfunded. Packed estimate $740.00. Year-1 commercial units authorized: 0. Stop before production tooling. No flight.
Team. Alex Meadow, packet owner and no-flight gate; Jordan Vale, flight research; Sam Reed, mechanical interface; Robin Keel, animal-welfare reviewer
Approved by. review pending. Alex Meadow, Planning draft C1, unsigned. The $250,000.00 research allowance is not drawn. Year-1 commercial units authorized: 0.
Preparation: Jordan Vale, scenario attribution, 2026-10-24. Signature: unsigned. Review: pending; no reviewer signature or date. Approval: withheld; no approver signature or date.